Ma Xiang-Yang, Yin Qing-Shui, Wu Zeng-Hui, Xia Hong, Liu Jing-Fa, Zhong Shi-Zhen
Department of Orthopaedics, Guangzhou Liuhuaqiao Hospital, Guangzhou, Peoples Republic of China.
Spine (Phila Pa 1976). 2005 Jul 1;30(13):1519-23. doi: 10.1097/01.brs.0000168546.17788.49.
Anatomic bony measurements were manually performed on 50 dry atlantoaxial vertebral complexes with an electronic digital caliper, and a reliable landmark for insertion of a pedicle screw in C1 vertebra was described and evaluated.
To investigate the feasibility of placing a screw in the C1 pedicle and evaluate the reliability of the C2 lateral mass as a landmark for determining the optimal site of screw entry.
The use of C1-C2 pedicle screws with the additional rods or plates has been an alternative method of stabilization for patients who are unsuitable for C1-C2 transarticular screw stabilization. However, the optimal portal of entry for the C1 pedicle screw is difficult to determine during surgery in the absence of reliable reference landmarks and sufficient relevant anatomic studies.
We manually measured 11 linear anatomic parameters related to the C1 lateral mass, its pedicle and posterior arch under the groove on 50 pairs of dry C1-C2 complexes harvested from cadavers. We also treated five patients with atlantoaxial instability with C1 and C2 pedicle screw fixation; the entry point of the C1 pedicle screw was ascertained by using C2 lateral mass as a landmark, and the position of the C1 pedicle screws in each case was evaluated with postoperative radiographs and computed tomography scans.
The mean mediolateral width and rostrocaudal height of C1 pedicle were 8.57 and 5.83 mm, respectively. The mean rostrocaudal height of C1 posterior lamina at the reference entry point for the screw was 4.59 mm. The mean rostrocaudal height of the C1 posterior arch under the vertebral artery groove was 3.88 mm at its medial one-third and 4.25 mm at its lateral one-third. The thinnest external diameter of the screw tract that was recorded was <4 mm in six (12%) specimens of C1 vertebrae. The center of C2 lateral mass was 1.51 mm lateral to the sagittal plane of the mediolateral midpoint of the C1 pedicle. The distance from the suggested screw entry point to C1 posterior tubercle was 22.15 mm, and the mean length of the screw tract was 28.55 mm. Ten C1 pedicle screws were placed exactly, without neural or vascular injury in all five patients.
The heights of the C1 pedicle, the posterior arch under the groove and the posterior lamina at the screw entry point are the major determinants for the possibility of placing pedicle screws in C1 of a given patient. This study indicates that it is feasible to place a 3.5-mm pedicle screw safely in C1 in most patients, and the lateral mass of C2 is a reliable anatomic landmark that can be easily identified to help the surgeon determine the optimal screw entry portal conveniently during surgery.
使用电子数字卡尺对50个干燥的寰枢椎复合体进行解剖学骨测量,并描述和评估C1椎弓根螺钉置入的可靠标志。
探讨C1椎弓根螺钉置入的可行性,并评估C2侧块作为确定螺钉最佳进钉点标志的可靠性。
对于不适合C1-C2经关节螺钉固定的患者,使用C1-C2椎弓根螺钉并附加棒或板是一种替代的稳定方法。然而,在手术中,由于缺乏可靠的参考标志和充分的相关解剖学研究,很难确定C1椎弓根螺钉的最佳进钉入口。
我们手动测量了从尸体获取的50对干燥的C1-C2复合体上与C1侧块、其椎弓根和沟下后弓相关的11个线性解剖参数。我们还对5例寰枢椎不稳患者进行了C1和C2椎弓根螺钉固定治疗;以C2侧块为标志确定C1椎弓根螺钉的进钉点,并通过术后X线片和计算机断层扫描评估每例患者C1椎弓根螺钉的位置。
C1椎弓根的平均内外宽度和前后高度分别为8.57mm和�.83mm。螺钉参考进钉点处C1后板的平均前后高度为4.59mm。椎动脉沟下C1后弓内侧三分之一处的平均前后高度为3.88mm,外侧三分之一处为˴.25mm。在6个(12%)C1椎骨标本中,记录到的螺钉通道最细外径<4mm。C2侧块中心位于C1椎弓根内外中点矢状面外侧1.51mm处。建议的螺钉进钉点到C1后结节的距离为22.15mm,螺钉通道的平均长度为28.55mm。在所有5例患者中,10枚C1椎弓根螺钉置入准确,无神经或血管损伤。
C1椎弓根高度、沟下后弓高度和螺钉进钉点处的后板高度是特定患者C1椎弓根螺钉置入可能性的主要决定因素。本研究表明,在大多数患者中,安全地在C1置入3.5mm椎弓根螺钉是可行的,C2侧块是一个可靠的解剖标志,在手术中很容易识别,有助于外科医生方便地确定最佳螺钉进钉入口。