Suppr超能文献

用于调强放射治疗的蒙特卡罗剂量计算中多叶准直器模型的开发与调试

Development and commissioning of a multileaf collimator model in monte carlo dose calculations for intensity-modulated radiation therapy.

作者信息

Jang Si Young, Vassiliev Oleg N, Liu H Helen, Mohan Radhe, Siebers Jeffrey V

机构信息

Department of Radiation Physics, The University of Texas M. D. Anderson Cancer Center, 1515 Holcombe Blvd., Houston, Texas 77030, USA.

出版信息

Med Phys. 2006 Mar;33(3):770-81. doi: 10.1118/1.2170598.

Abstract

A multileaf collimator (MLC) model, "MATMLC," was developed to simulate MLCs for Monte Carlo (MC) dose calculations of intensity-modulated radiation therapy (IMRT). This model describes MLCs using matrices of regions, each of which can be independently defined for its material and geometry, allowing flexibility in simulating MLCs from various manufacturers. The free parameters relevant to the dose calculations with this MLC model included MLC leaf density, interleaf air gap, and leaf geometry. To commission the MLC model and its free parameters for the Varian Millennium MLC-120 (Varian Oncology Systems, Palo Alto, CA), we used the following leaf patterns: (1) MLC-blocked fields to test the effects of leaf transmission and leakage; (2) picket-fence fields to test the effects of the interleaf air gap and tongue-groove design; and (3) abutting-gap fields to test the effects of rounded leaf ends. Transmission ratios and intensity maps for these leaf patterns were calculated with various sets of modeling parameters to determine their dosimetric effects, sensitivities, and their optimal combinations to give the closest agreement with measured results. Upon commissioning the MLC model, we computed dose distributions for clinical IMRT plans using the MC system and verified the results with those from ion chamber and thermoluminescent dosimeter measurements in water phantoms and anthropomorphic phantoms. This study showed that the MLC transmission ratios were strongly dependent on both leaf density and the interleaf air gap. The effect of interleaf air gap and tongue-groove geometry can be determined most effectively through fence-type MLC patterns. Using the commissioned MLC model, we found that the calculated dose from the MC system agreed with the measured data within clinically acceptable criteria from low- to high-dose regions, showing that the model is acceptable for clinical applications.

摘要

开发了一种多叶准直器(MLC)模型“MATMLC”,用于模拟多叶准直器,以进行调强放射治疗(IMRT)的蒙特卡罗(MC)剂量计算。该模型使用区域矩阵描述多叶准直器,每个区域的材料和几何形状均可独立定义,从而在模拟不同制造商的多叶准直器时具有灵活性。与该多叶准直器模型剂量计算相关的自由参数包括多叶准直器叶片密度、叶片间气隙和叶片几何形状。为了对Varian Millennium MLC - 120(Varian Oncology Systems,帕洛阿尔托,加利福尼亚州)的多叶准直器模型及其自由参数进行调试,我们使用了以下叶片模式:(1)多叶准直器遮挡野,以测试叶片透射和泄漏的影响;(2)栅栏野,以测试叶片间气隙和舌槽设计的影响;(3)邻接间隙野,以测试叶片末端倒圆的影响。针对这些叶片模式,使用不同组的建模参数计算透射率和强度图,以确定它们的剂量学效应、敏感性以及能给出与测量结果最接近一致性的最佳组合。在调试多叶准直器模型后,我们使用MC系统计算了临床IMRT计划的剂量分布,并通过水模体和人体模型中的电离室和热释光剂量计测量结果对结果进行了验证。本研究表明,多叶准直器透射率强烈依赖于叶片密度和叶片间气隙。叶片间气隙和舌槽几何形状的影响可以通过栅栏式多叶准直器模式最有效地确定。使用调试后的多叶准直器模型,我们发现MC系统计算得到的剂量在临床可接受标准范围内与低剂量区到高剂量区的测量数据一致,表明该模型可用于临床应用。

文献AI研究员

20分钟写一篇综述,助力文献阅读效率提升50倍。

立即体验

用中文搜PubMed

大模型驱动的PubMed中文搜索引擎

马上搜索

文档翻译

学术文献翻译模型,支持多种主流文档格式。

立即体验