Thawrani Dinesh P, Glos David L, Coombs Matthew T, Bylski-Austrow Donita I, Sturm Peter F
*Department of Orthopaedics, Cincinnati Children's Hospital Medical Center, Cincinnati, OH; and †University of Cincinnati, Cincinnati, OH.
Spine (Phila Pa 1976). 2014 Jun 15;39(14):E826-32. doi: 10.1097/BRS.0000000000000367.
Biomechanical study in a porcine model.
To determine whether transverse process hooks (TPHs) placed at the proximal end of a long posterior spinal fusion construct provide a more gradual transition to normal motion of the adjacent cephalad motion segment compared with an all pedicle screw (APS) construct.
Proximal junctional kyphosis after instrumentation with long posterior spinal constructs has been increasingly associated with incidence of adjacent segment pathologies. Clinical studies have suggested that proximal anchor type may affect the incidence of proximal junctional kyphosis.
Biomechanical tests were conducted on porcine thoracic spines before and after implantation of a long spinal fusion construct. In all specimens, dual long rods (Co-Cr) were implanted posteriorly using pedicle screws at T7-T15. Upper instrumented vertebra, T6, received either TPHs (n = 7) or pedicle screws (APSs) (n = 6). Each specimen was tested in flexion-extension then lateral bending. Moments were applied, and vertebral displacements were recorded. Range of motion (ROM) and stiffness (K) were determined for each motion segment. Differences between TPH and APS at the transition were determined using t tests.
In flexion-extension, ROM at the most proximal instrumented motion segment was 9% of control for APS versus 21% of control for TPH. Difference between APS and TPH at UIV was 0.5° (P < 0.008). Stiffness of TPH at T6-T7 was significantly lower than APS in FE (P < 0.003). For APS, the greatest mean ROM occurred at the first uninstrumented segment, whereas TPH maintained the pattern of monotonic increases in mean ROM from distal to proximal.
TPHs at the upper instrumented vertebra provided a more gradual transition to normal motion compared with pedicle screws in long posterior spinal fusion constructs. TPH at the upper instrumented vertebra may be postulated to decrease the incidence of postoperative proximal junctional kyphosis compared with APS.
N/A.
在猪模型上进行的生物力学研究。
确定与全椎弓根螺钉(APS)结构相比,置于长节段后路脊柱融合结构近端的横突钩(TPH)是否能更平缓地过渡到相邻上位运动节段的正常运动。
使用长节段后路脊柱结构进行器械固定后,近端交界性后凸与相邻节段病变的发生率越来越相关。临床研究表明,近端固定类型可能影响近端交界性后凸的发生率。
在植入长节段脊柱融合结构前后,对猪胸椎进行生物力学测试。在所有标本中,使用椎弓根螺钉在T7 - T15后方植入双根长杆(钴铬合金)。上位固定椎体T6接受TPH(n = 7)或椎弓根螺钉(APS)(n = 6)。每个标本先进行屈伸测试,然后进行侧弯测试。施加力矩并记录椎体位移。确定每个运动节段的活动度(ROM)和刚度(K)。使用t检验确定TPH和APS在过渡处的差异。
在屈伸运动中,最近端固定运动节段的ROM,APS组为对照组的9%,而TPH组为对照组的21%。UIV处APS和TPH的差异为0.5°(P < 0.008)。在屈伸运动中,T6 - T7处TPH的刚度显著低于APS(P < 0.003)。对于APS,最大平均ROM出现在第一个未固定节段,而TPH保持平均ROM从远端到近端单调增加的模式。
与长节段后路脊柱融合结构中的椎弓根螺钉相比,上位固定椎体处的TPH能更平缓地过渡到正常运动。与APS相比,可推测上位固定椎体处的TPH可降低术后近端交界性后凸的发生率。
无。