Suppr超能文献

在共研磨中辅料对减轻研磨诱导的药物活性成分无定形化或结构无序的影响。

Influence of excipients in comilling on mitigating milling-induced amorphization or structural disorder of crystalline pharmaceutical actives.

机构信息

Department of Pharmacy, National University of Singapore, Block S4, 18, Science Drive 4, Singapore 117543, Singapore.

出版信息

J Pharm Sci. 2010 May;99(5):2462-74. doi: 10.1002/jps.21998.

Abstract

The feasibility of using excipients to suppress the amorphization or structural disorder of crystalline salbutamol sulphate (SS) during milling was investigated. SS was subjected to ball-milling in the presence of alpha-lactose monohydrate (LAC), adipic acid (AA), magnesium stearate (MgSt), or polyvinyl pyrrolidone (PVP). X-ray powder diffraction, dynamic vapor sorption (DVS), high sensitivity differential scanning calorimetry (HSDSC) were used to analyze the crystallinity of the milled mixtures. Comilling with crystalline excipients, LAC, AA, and MgSt proved effective in reducing the amorphization of SS. LAC, AA, or MgSt acting as seed crystals to induce recrystallization of amorphous SS formed by milling. During comilling, both SS and LAC turned predominantly amorphous after 45 min but transformed back to a highly crystalline state after 60 min. Amorphous content was below the detection limits of DVS (0.5%) and HSDSC (5%). Comilled and physical mixtures of SS and ALM were stored under normal and elevated humidity conditions. This was found to prevent subsequent changes in crystallinity and morphology of comilled SS:LAC as compared to significant changes in milled SS and physical mixture. These results demonstrate a promising application of comilling with crystalline excipients in mitigating milling induced amorphization of pharmaceutical actives.

摘要

研究了在研磨过程中使用辅料抑制结晶硫酸沙丁胺醇(SS)无定形化或结构无序的可行性。在α-乳糖一水合物(LAC)、己二酸(AA)、硬脂酸镁(MgSt)或聚乙烯吡咯烷酮(PVP)存在下,将 SS 进行球磨。使用 X 射线粉末衍射、动态蒸汽吸附(DVS)、高灵敏度差示扫描量热法(HSDSC)分析研磨混合物的结晶度。与结晶辅料共研磨时,LAC、AA 和 MgSt 可有效降低 SS 的无定形化。LAC、AA 或 MgSt 作为晶种,诱导由研磨形成的无定形 SS 重结晶。在共研磨过程中,SS 和 LAC 在 45 分钟后主要变为无定形,但在 60 分钟后又转变为高度结晶状态。无定形含量低于 DVS(0.5%)和 HSDSC(5%)的检测限。将 SS 和 ALM 的共研磨和物理混合物在正常和高湿度条件下储存。与研磨 SS 和物理混合物相比,这发现可防止共研磨 SS:LAC 的结晶度和形态随后发生变化。这些结果表明,使用结晶辅料共研磨在减轻药物活性物质研磨诱导的无定形化方面具有有前途的应用。

文献检索

告别复杂PubMed语法,用中文像聊天一样搜索,搜遍4000万医学文献。AI智能推荐,让科研检索更轻松。

立即免费搜索

文件翻译

保留排版,准确专业,支持PDF/Word/PPT等文件格式,支持 12+语言互译。

免费翻译文档

深度研究

AI帮你快速写综述,25分钟生成高质量综述,智能提取关键信息,辅助科研写作。

立即免费体验