Graduate School of Biomedical Engineering/Graduate School of Engineering, Tohoku University, Sendai, Japan.
IEEE Trans Ultrason Ferroelectr Freq Control. 2009 Nov;56(11):2450-62. doi: 10.1109/TUFFC.2009.1332.
Artery-wall motion due to the pulsation of the heart is often measured to evaluate mechanical properties of the arterial wall. Such motion is thought to occur only in the arterial radial direction because the main source of the motion is an increase of blood pressure. However, it has recently been reported that the artery also moves in the longitudinal direction. Therefore, a 2-D motion estimator is required even when the artery is scanned in the longitudinal direction because the arterial wall moves both in the radial (axial) and longitudinal (lateral) directions. Methods based on 2-D correlation of RF echoes are often used to estimate the lateral displacement together with axial displacement. However, these methods require much interpolation of the RF echo or correlation function to achieve a sufficient resolution in the estimation of displacement. To overcome this problem, Jensen et al. modulated the ultrasonic field in the lateral direction at a designed spatial frequency to use the lateral phase for the estimation of lateral motion. This method, namely, the lateral modulation method, generates complex signals whose phases change depending on the lateral motion. Therefore, the lateral displacement can be estimated with a good resolution without interpolation, although special beamformers are required. The present paper describes a method that can be applied to ultrasonic echoes obtained by a conventional beamformer to estimate lateral displacements using the phases of lateral fluctuations of ultrasonic echoes. In the proposed method, complex signals were generated by the Hilbert transform, and the phase shift was estimated by correlation-based estimators. The proposed method was validated using a cylindrical phantom mimicking an artery. The error in the lateral displacement estimated by the proposed method was 13.5% of the true displacement of 0.5 mm with a kernel size used for calculating the correlation function of 0.6 mm in the lateral direction, which was slightly smaller than the width at -20 dB of the maximum lateral ultrasonic field (about 0.8 mm).
由于心脏的脉动,动脉壁的运动经常被测量,以评估动脉壁的机械特性。这种运动被认为仅发生在动脉的径向方向,因为运动的主要来源是血压的增加。然而,最近有报道称,动脉也会在纵向方向上移动。因此,即使在纵向方向上扫描动脉,也需要一个 2-D 运动估计器,因为动脉壁会同时在径向(轴向)和纵向(侧向)方向上移动。基于 RF 回波的 2-D 相关的方法通常用于估计侧向位移和轴向位移。然而,这些方法需要对 RF 回波或相关函数进行大量插值,以在位移估计中实现足够的分辨率。为了解决这个问题,Jensen 等人在设计的空间频率上在侧向调制超声场,以利用侧向相位来估计侧向运动。这种方法,即侧向调制方法,产生了复杂的信号,其相位随侧向运动而变化。因此,即使需要特殊的波束形成器,也可以在不插值的情况下以良好的分辨率估计侧向位移。本文描述了一种可应用于常规波束形成器获得的超声回波的方法,通过利用超声回波的侧向波动的相位来估计侧向位移。在提出的方法中,通过希尔伯特变换生成复信号,并通过基于相关的估计器来估计相位移动。该方法使用模拟动脉的圆柱形体模进行了验证。使用用于计算相关函数的核大小为 0.6mm 的侧向方向上,估计的侧向位移的误差为 0.5mm 真实位移的 13.5%,这略小于最大侧向超声场的-20dB 带宽(约 0.8mm)。