Food Research and Development Laboratory, Morinaga Milk Industry Co. Ltd., Zama, Kanagawa 228-8583, Japan.
J Dairy Sci. 2010 Jul;93(7):2827-37. doi: 10.3168/jds.2009-2960.
Sodium hexametaphosphate (SHMP) is commonly used as an emulsifying salt (ES) in process cheese, although rarely as the sole ES. It appears that no published studies exist on the effect of SHMP concentration on the properties of process cheese when pH is kept constant; pH is well known to affect process cheese functionality. The detailed interactions between the added phosphate, casein (CN), and indigenous Ca phosphate are poorly understood. We studied the effect of the concentration of SHMP (0.25-2.75%) and holding time (0-20min) on the textural and rheological properties of pasteurized process Cheddar cheese using a central composite rotatable design. All cheeses were adjusted to pH 5.6. The meltability of process cheese (as indicated by the decrease in loss tangent parameter from small amplitude oscillatory rheology, degree of flow, and melt area from the Schreiber test) decreased with an increase in the concentration of SHMP. Holding time also led to a slight reduction in meltability. Hardness of process cheese increased as the concentration of SHMP increased. Acid-base titration curves indicated that the buffering peak at pH 4.8, which is attributable to residual colloidal Ca phosphate, was shifted to lower pH values with increasing concentration of SHMP. The insoluble Ca and total and insoluble P contents increased as concentration of SHMP increased. The proportion of insoluble P as a percentage of total (indigenous and added) P decreased with an increase in ES concentration because of some of the (added) SHMP formed soluble salts. The results of this study suggest that SHMP chelated the residual colloidal Ca phosphate content and dispersed CN; the newly formed Ca-phosphate complex remained trapped within the process cheese matrix, probably by cross-linking CN. Increasing the concentration of SHMP helped to improve fat emulsification and CN dispersion during cooking, both of which probably helped to reinforce the structure of process cheese.
六偏磷酸钠(SHMP)通常用作加工干酪中的乳化盐(ES),尽管很少作为唯一的 ES。似乎没有关于在 pH 值保持不变的情况下,SHMP 浓度对加工干酪性质的影响的已发表研究;众所周知,pH 值会影响加工干酪的功能。添加的磷酸盐、酪蛋白(CN)和内源性磷酸钙之间的详细相互作用知之甚少。我们使用中心复合旋转设计研究了 SHMP 浓度(0.25-2.75%)和保持时间(0-20 分钟)对巴氏杀菌加工切达奶酪的质构和流变特性的影响。所有奶酪的 pH 值均调整至 5.6。加工干酪的熔融性(如小振幅振荡流变学中的损耗角正切参数降低、流动程度和施赖伯测试中的熔融面积所表示的)随 SHMP 浓度的增加而降低。保持时间也导致熔融性略有降低。加工干酪的硬度随 SHMP 浓度的增加而增加。酸碱滴定曲线表明,归因于残余胶体磷酸钙的缓冲峰在 pH 4.8 处,随着 SHMP 浓度的增加而向较低 pH 值移动。不溶性 Ca 和总磷及不溶性磷含量随 SHMP 浓度的增加而增加。由于部分(添加)SHMP 形成可溶性盐,不溶性磷占总磷(内源性和添加)的比例随 ES 浓度的增加而降低。本研究结果表明,SHMP 螯合了残余胶体磷酸钙含量并分散了 CN;新形成的钙-磷复合物仍然被困在加工奶酪基质中,可能是通过交联 CN。增加 SHMP 的浓度有助于改善烹饪过程中的脂肪乳化和 CN 分散,这两者都可能有助于加强加工奶酪的结构。