Markolf K L, Gorek J F, Kabo J M, Shapiro M S
Division of Orthopedic Surgery, University of California, Los Angeles 90024-1795.
J Bone Joint Surg Am. 1990 Apr;72(4):557-67.
A new technique was used to measure the resultant forces in the anterior cruciate ligament during a series of loading experiments on seventeen fresh-frozen cadaver specimens. The base of the ligament's tibial attachment was mechanically isolated with a coring cutter, and a specially designed load-transducer was fixed to the bone-plug that contained the ligament's tibial insertion so that the resultant forces were directly measured by the load-cell. Although the magnitudes of values for forces varied considerably between specimens for a given test condition, the patterns of loading with respect to direction of loading and the angle of flexion of the knee were remarkably consistent. Passive extension of the knee generated forces in the ligament only during the last 10 degrees of extension; at 5 degrees of hyperextension, the forces ranged from fifty to 240 newtons (mean, 118 newtons). When a 200-newton pull of the quadriceps tendon was applied to extend a knee slowly against tibial resistance, however, the force in the ligament increased at all angles of flexion of the knee. Internal tibial torque always generated greater forces in the ligament than did external tibial torque; higher forces were recorded as the knee was extended. The greatest forces (133 to 370 newtons) were generated when ten newton-meters of internal tibial torque was applied to a hyperextended knee. Fifteen newton-meters of applied varus moment generated forces of ninety-four to 177 newtons at full extension; fifteen newton-meters of applied valgus moment generated a mean force of fifty-six newtons, which remained unchanged with flexion of the knee. The force during straight anterior translation of the tibia was approximately equal to the anterior force applied to the tibia. The application of 925 newtons of tibiofemoral contact force reduced the mean force in the ligament that was generated by 200 newtons of anterior pull on the tibia by 36 per cent at full extension and 46 per cent at 20 degrees of flexion.
在对17个新鲜冷冻尸体标本进行的一系列加载实验中,采用了一种新技术来测量前交叉韧带中的合力。用取芯刀将韧带胫骨附着处的基部进行机械分离,并将一个专门设计的载荷传感器固定在包含韧带胫骨插入部的骨栓上,以便通过测力传感器直接测量合力。尽管在给定测试条件下,不同标本之间力的值大小差异很大,但就加载方向和膝关节屈曲角度而言,加载模式非常一致。膝关节的被动伸展仅在最后10度伸展时才在韧带中产生力;在过伸5度时,力的范围为50至240牛顿(平均118牛顿)。然而,当施加200牛顿的股四头肌肌腱拉力以缓慢伸展膝关节抵抗胫骨阻力时,韧带中的力在膝关节的所有屈曲角度都会增加。胫骨内扭矩在韧带中产生的力总是比胫骨外扭矩产生的力更大;随着膝关节伸展,记录到的力更高。当对过伸的膝关节施加10牛顿·米的胫骨内扭矩时,会产生最大力(133至370牛顿)。施加15牛顿·米的内翻力矩在完全伸展时产生94至177牛顿的力;施加15牛顿·米的外翻力矩产生平均56牛顿的力,该力随膝关节屈曲保持不变。胫骨向前直线平移时的力大约等于施加在胫骨上的向前力。在完全伸展时,施加925牛顿的胫股接触力可使因胫骨向前拉力200牛顿而在韧带中产生的平均力降低36%,在屈曲20度时降低46%。