Suppr超能文献

具有聚乙二醇冠的聚合物囊泡:温度变化引起的结构变化和控制释放。

Polymersomes with PEG corona: structural changes and controlled release induced by temperature variation.

机构信息

Institut Curie, Centre de Recherche, 75248 Paris, France.

出版信息

Langmuir. 2013 Feb 5;29(5):1356-69. doi: 10.1021/la304199z. Epub 2013 Jan 23.

Abstract

Thermoresponsive behavior of different kinds of polymersomes was studied using small angle neutron scattering (SANS), transmission electron microscopy (TEM), and proton nuclear magnetic resonance ((1)H NMR). The polymersomes were made of block copolymers containing a 2000 Da polyethylene glycol (PEG) as a hydrophilic block and either a liquidlike polymer (e.g., PBA: polybutylacrylate), a solidlike polymer (PS: polystyrene), or a liquid crystalline (LC) polymer as a hydrophobic block. Structural changes in polymersomes are driven in all cases by the critical dehydration temperature of PEG corona, which is closely related to the chemical structure and chain mobility of the hydrophobic block. No structural changes occur upon heating from 25 to 75 °C in the liquidlike polymersomes where the critical dehydration temperature of PEG should be higher than 75 °C. In contrast, glassy PEG-b-PS polymersomes and LC polymersomes show structural changes around 55 °C, which corresponds to the critical dehydration temperature of PEG in those block copolymers. Furthermore, the structural changes depend on the properties of the hydrophobic layer. Glassy PEG-b-PS polymersomes aggregate together above 55 °C, but the bilayer membrane is robust enough to remain intact. This aggregation is reversible, and rather separate polymersomes are recovered upon cooling. However, LC polymersomes display drastic and irreversible structural changes when heated above ∼55 °C. These changes are dependent on the LC structures of the hydrophobic layer. Nematic LC polymersomes turn into thick-walled capsules, whereas smectic LC polymersomes collapse into dense aggregates. As these drastic and irreversible changes decrease or remove the inner compartment volume of the vesicle, LC polymersomes can be used for thermal-responsive controlled release, as shown by a study of calcein release. Finally, toxicity studies proved that LC polymersomes were noncytotoxic and had no effect on cell morphology.

摘要

使用小角中子散射(SANS)、透射电子显微镜(TEM)和质子核磁共振((1)H NMR)研究了不同类型聚合物囊泡的温敏行为。聚合物囊泡由嵌段共聚物组成,嵌段共聚物包含 2000 Da 的聚乙二醇(PEG)作为亲水性嵌段,以及液态聚合物(例如 PBA:聚丁基丙烯酸酯)、固态聚合物(PS:聚苯乙烯)或液晶(LC)聚合物作为疏水性嵌段。在所有情况下,聚合物囊泡的结构变化都是由 PEG 冠层的临界脱水温度驱动的,临界脱水温度与疏水性嵌段的化学结构和链迁移率密切相关。在液态聚合物囊泡中,当温度从 25°C 加热到 75°C 时,不会发生结构变化,因为 PEG 的临界脱水温度应该高于 75°C。相比之下,玻璃态 PEG-b-PS 聚合物囊泡和 LC 聚合物囊泡在 55°C 左右表现出结构变化,这与这些嵌段共聚物中 PEG 的临界脱水温度相对应。此外,结构变化取决于疏水性层的性质。玻璃态 PEG-b-PS 聚合物囊泡在高于 55°C 时聚集在一起,但双层膜足够坚固,保持完整。这种聚集是可逆的,冷却后会恢复到相对独立的聚合物囊泡。然而,当加热到高于约 55°C 时,LC 聚合物囊泡会发生剧烈且不可逆的结构变化。这些变化取决于疏水性层的 LC 结构。向列 LC 聚合物囊泡变成厚壁胶囊,而层状 LC 聚合物囊泡塌陷成密集的聚集体。由于这些剧烈且不可逆的变化减少或消除了囊泡的内部隔室体积,因此 LC 聚合物囊泡可用于热响应控制释放,如通过研究钙黄绿素释放来证明。最后,毒性研究证明 LC 聚合物囊泡无细胞毒性,对细胞形态没有影响。

文献AI研究员

20分钟写一篇综述,助力文献阅读效率提升50倍。

立即体验

用中文搜PubMed

大模型驱动的PubMed中文搜索引擎

马上搜索

文档翻译

学术文献翻译模型,支持多种主流文档格式。

立即体验