Suppr超能文献

最大限度提高跟骨后关节面骨折螺钉固定安全性的研究:尸体放射解剖学研究。

Maximizing safety in screw placement for posterior facet fixation in calcaneus fractures: a cadaveric radio-anatomical study.

机构信息

Department of Orthopaedics and Rehabilitation, University of Iowa, Iowa City, IA, USA.

出版信息

Foot Ankle Int. 2013 Sep;34(9):1279-85. doi: 10.1177/1071100713487182. Epub 2013 Apr 18.

Abstract

BACKGROUND

Successful screw fixation of reduced posterior facet fragments to the unexposed, nondisplaced sustentaculum tali avoids breaching the subtalar joint or disrupting surrounding soft tissue structures. Safe passage for screw fixation through this narrow bony corridor has not been rigorously defined.

METHODS

Computed tomography scans of 8 cadaveric feet were digitally reconstructed in 3-D; 3.5-mm-diameter screws were simulated, aiming at the center of the sustentaculum tali from 5 locations (0%, 25%, 50%, 75%, and 100%) along the posterolateral facet joint. The range of entry points, screw paths trajectories, and screw lengths that did not breach the subtalar joint or the medial calcaneal cortex were evaluated.

RESULTS

To prevent violation of the subtalar joint or the medial calcaneal cortex while reaching the center of the sustentaculum tali, screws must be inserted at least 5 mm below the joint line. Screw placement 15 ± 1 mm below the posterior facet measured perpendicular to the joint line provided the widest safe corridor with the trajectory of the ranges from 6 to 36 degrees parallel to the joint depending on the location along the posterior facet and 20 ± 2 degrees perpendicular to the joint at all locations. The average maximal length of screws placed at the ideal entry points ranged from 44 to 46 mm, longest at the 100% location and shortest at the 25% location.

CONCLUSIONS

Operative guidelines facilitating instrumentation into the sustentaculum tali have been defined applying to most calcanei, assuming the fractures are well reduced: screws, approximately 40 mm in length, should be started 15 mm below the posterior facet measured perpendicular to the joint line and aimed 20 degrees perpendicular to the joint line toward the joint and 6 to 36 degrees anteversion parallel to the joint line increasing at each position from anterior to posterior.

CLINICAL RELEVANCE

The operative guidelines described in this study may assist surgeons in the placement of screws for the fixation of posterior facet fragments to the sustentaculum tali.

摘要

背景

成功地将后关节面骨碎片用螺钉固定到未暴露、未移位的跟骨载距突上,可避免破坏距下关节或破坏周围的软组织结构。通过这条狭窄的骨道安全地固定螺钉尚未得到严格定义。

方法

对 8 例尸体足的 CT 扫描进行了 3D 数字重建;模拟了 3.5mm 直径的螺钉,从后外侧关节面的 5 个位置(0%、25%、50%、75%和 100%)瞄准跟骨载距突的中心。评估了不破坏距下关节或内跟骨皮质的进钉点范围、螺钉路径轨迹和螺钉长度。

结果

为了防止在到达跟骨载距突中心时违反距下关节或内跟骨皮质,螺钉必须至少低于关节线 5mm 插入。垂直于关节线测量,后关节面下 15±1mm 处放置螺钉可提供最宽的安全通道,其轨迹范围从 6 度到 36 度与关节平行,具体取决于后关节面的位置,所有位置与关节成 20±2 度垂直。在理想的进钉点放置的螺钉的平均最大长度范围为 44 至 46mm,在 100%位置最长,在 25%位置最短。

结论

在大多数跟骨骨折得到良好复位的情况下,应用该操作指南可指导器械进入跟骨载距突:长度约 40mm 的螺钉应在后关节面下垂直于关节线测量 15mm 处开始,垂直于关节线 20 度向关节方向进钉,与关节线成 6 至 36 度前倾角平行于关节线,从前方到后方每个位置增加。

临床相关性

本研究描述的操作指南可帮助外科医生将后关节面骨碎片用螺钉固定到跟骨载距突上。

文献AI研究员

20分钟写一篇综述,助力文献阅读效率提升50倍。

立即体验

用中文搜PubMed

大模型驱动的PubMed中文搜索引擎

马上搜索

文档翻译

学术文献翻译模型,支持多种主流文档格式。

立即体验