Department of Prosthodontics, Faculty of Dentistry, Marmara University, Basibuyuk, Istanbul, Turkey.
J Prosthodont. 2019 Jan;28(1):e186-e194. doi: 10.1111/jopr.12618. Epub 2017 Apr 6.
To examine the application of physical vapor deposition (PVD) silica coating as an approach to retard low temperature degradation (LTD) for dental applications. Accelerated aging characteristics of heat- and surface-treated zirconia material were also investigated by exposing specimens to hydrothermal treatment.
The specimens (90 disc-shaped specimens [15 mm ×1.2 mm]) were divided into 9 groups (n = 10) according to the test protocol: Ctrl, control (no surface treatment); Ag, autoclave aging; GrAg, grinding + aging; SiAg, silica coating + aging; GrSiAg, grinding + silica coating + aging; 3FAg, 3-time firing + aging; Gr3FAg, grinding + 3-time firing + aging; 5FAg, 5-time firing + aging; Gr5FAg, grinding + 5-time firing + aging. Accelerated aging was performed in a steam autoclave (134°C, 2 bars) for 12 hours. Following each treatment protocol, X-ray diffraction (XRD) analysis was used to estimate the relative amount of monoclinic phase and corresponding transformed zone depth (TZD). Additionally, a biaxial flexure test was used to calculate the flexural strength. Statistical analysis was conducted with one-way ANOVA and Fisher's LSD test (p < 0.05).
The tetragonal-to-monoclinic transformation was retarded by PVD silica coating only on ground surfaces. Ground and heat-treated specimens exhibited the lowest monoclinic content after aging. The biaxial flexural strength value of the GrAg group was significantly higher than the values in all of the other groups except the SiAg group. The flexural strength value of the GrSiAg group was significantly higher than that of the 3FAg group. There was no statistically significant difference between the other groups (p > 0.05).
Grinding decreased the susceptibility of zirconia to LTD and increased the flexural strength. PVD silica coating and repeated firing decreased the monoclinic content only in ground specimens during aging.
研究物理气相沉积(PVD)二氧化硅涂层在延缓牙科应用低温降解(LTD)方面的应用。通过对样品进行水热处理,还研究了热和表面处理氧化锆材料的加速老化特性。
根据测试方案,将 90 个(90 个圆盘状试件[15mm×1.2mm])试件分为 9 组(n=10):对照(无表面处理)、高压釜老化(Ag)、研磨+老化(GrAg)、二氧化硅涂层+老化(SiAg)、研磨+二氧化硅涂层+老化(GrSiAg)、3 次烧制+老化(3FAg)、研磨+3 次烧制+老化(Gr3FAg)、5 次烧制+老化(5FAg)、研磨+5 次烧制+老化(Gr5FAg)。在蒸汽高压釜中(134°C,2 巴)进行加速老化 12 小时。在每种处理方案之后,使用 X 射线衍射(XRD)分析来估计单斜相的相对量和相应的转化区深度(TZD)。此外,还进行了双轴弯曲试验来计算弯曲强度。采用单因素方差分析和 Fisher LSD 检验(p<0.05)进行统计学分析。
PVD 二氧化硅涂层仅在研磨表面上延缓了四方相到单斜相的转变。研磨和热处理后的试件在老化后表现出最低的单斜相含量。GrAg 组的双轴弯曲强度值明显高于除 SiAg 组之外的所有其他组的值。GrSiAg 组的弯曲强度值明显高于 3FAg 组。其他组之间无统计学差异(p>0.05)。
研磨降低了氧化锆对 LTD 的敏感性并提高了弯曲强度。PVD 二氧化硅涂层和重复烧制仅在老化期间降低了研磨后的试件中单斜相的含量。