Liu Xiang, Wang Jing-Yao, Wu Juan-Juan, Peng Fei, Wang Kai-Jun
State Key Joint Laboratory of Environment Simulation and Pollution Control, School of Environment, Tsinghua University, Beijing 100084, China.
Huan Jing Ke Xue. 2019 Jul 8;40(7):3126-3134. doi: 10.13227/j.hjkx.201811219.
Application of microalgae in wastewater treatment is regarded as a potential green technology. However, its engineering application has been largely hindered because of the difficulty of biomass separation and harvesting. This study aimed to identify the key parameters influencing the process of microalgae immobilization. To do this, the study focused on immobilization technology and , and employed the response surface methodology (RSM) and the Box-Behnken design (BBD). In an evaluation of the performance of microalgae beads, the fixing agent concentration, the cross-linking agent concentration, and the cross-linking time were selected as the independent variables, and the mechanical strength, the mass transfer rate, and the growth rate of immobilized microalgae beads were the response values. The optimal conditions and the uptake potential of the microalgae beads with respect to ammonia nitrogen (NH-N) were further explored and analyzed. The results showed that the optimal parameters for the preparation of immobilized microalgae beads were 5%, 2%, and 16 h, and the maximum removal capacity was obtained using mixotrophic cultivation with an embedding density of 1×10 cells·mL and an organic matter concentration of 300 mg·L. In addition, the removal capacity of immobilized microalgae with respect to high concentrations of NH-N was significantly higher than for free-living microalgae. When the initial concentrations of NH-N were approximately 50 and 70 mg·L, NH-N was removed by the immobilized microalgae (after a 5-day mixotrophic cultivation) at a rate of (96.6±0.1)% and (65.2±4.5)%, respectively. With an initial NH-N concentration of 30 mg·L, the dominance of free-living microalgae was clear, with a removal rate of (97.8±0.6)% after a 3-day cultivation. However, under heterotrophic cultivation, the removal rate of NH-N by immobilized microalgae was generally low and gradually decreased with increasing concentrations. When the initial concentration was approximately 30 mg·L, the removal rate was only (49.0±3.1)%. This study provides new prospects for sustainable urban wastewater treatment, a new approach for resource recycling, and a strong theoretical foundation for the popularization and application of microalgae in wastewater treatment.
微藻在废水处理中的应用被视为一种潜在的绿色技术。然而,由于生物质分离和收获的困难,其工程应用在很大程度上受到了阻碍。本研究旨在确定影响微藻固定化过程的关键参数。为此,该研究聚焦于固定化技术,并采用响应面法(RSM)和Box-Behnken设计(BBD)。在对微藻珠性能的评估中,选择固定剂浓度、交联剂浓度和交联时间作为自变量,而固定化微藻珠的机械强度、传质速率和生长速率为响应值。进一步探索和分析了微藻珠对氨氮(NH-N)的最佳条件和吸收潜力。结果表明,制备固定化微藻珠的最佳参数为5%、2%和16小时,在混合营养培养条件下,包埋密度为1×10细胞·mL且有机物浓度为300 mg·L时可获得最大去除能力。此外,固定化微藻对高浓度NH-N的去除能力明显高于游离微藻。当NH-N的初始浓度约为50和70 mg·L时,固定化微藻(经过5天混合营养培养)对NH-N的去除率分别为(96.6±0.1)%和(65.2±4.5)%。当初始NH-N浓度为30 mg·L时,游离微藻占优势,经过3天培养后去除率为(97.8±0.6)%。然而,在异养培养条件下,固定化微藻对NH-N的去除率普遍较低,并随着浓度增加而逐渐降低。当初始浓度约为30 mg·L时,去除率仅为(49.0±3.1)%。本研究为城市可持续废水处理提供了新的前景,为资源回收提供了新方法,并为微藻在废水处理中的推广应用提供了坚实的理论基础。