Pichler Christian, Oberparleiter Stefan, Lackner Roman
Material Technology Innsbruck, University of Innsbruck, Technikerstraße 13, A-6020 Innsbruck, Austria.
Polymers (Basel). 2023 Sep 14;15(18):3770. doi: 10.3390/polym15183770.
In this paper, the experimental characterization of the viscoelastic properties of thermoplastic polyurethane (TPU) samples through creep experiments is presented. Experiments were conducted at different constant temperature levels (15, 25, and 35 ∘C), for three different tensile stress levels (0.3, 0.5, and 0.7 MPa), and at different physisorbed water contents, providing access to: (i) the temperature dependency of creep parameters and (ii) the assessment, if behavior is indeed viscoelastic. The physisorbed water content was achieved by exposing virgin samples to environments with relative humidity ranging from 0 to 80 percent until mass stability was reached. Creep tests were conducted immediately afterwards with this particular humidity level. The main results of this study are as follows. The temperature dependency of the obtained creep parameters is well described in Arrhenius plots. With regard to water content, two prototype material responses were observed in the experimental program and accurately modeled using the following fractional-type models: (i) Scott Blair-type (i.e., power-law-type) only behavior, pronounced for the combination of low water content/low temperature; (ii) combined Scott Blair plus Lomnitz (i.e., log-type) behavior for high water content/high temperature. This change in behavior associated with certain thresholds for the specified environmental conditions (temperature and relative humidity) may indicate the initiation of hydrogen bond breakage and rearrangement (carbamate H-bonds and physisorbed water H-bonds). Regarding the short-term or quasi-instantaneous behavior, the Scott Blair element seems highly appropriate and may be better suited than the standard elastic model: the Hookean spring. We associated Scott Blair behavior with the load-induced, quasi-instantaneous re-arrangement of polymer network chains. The secondary viscoelastic mechanism associated with the Lomnitz element, hydrogen bond breakage and rearrangement, comes into play for higher temperatures and/or higher physisorbed water contents. In this case, the contribution of the two constitutive elements is well separated due to the large number of the characteristic time of the Lomnitz element, much larger than the respective value for the Scott Blair element.
本文介绍了通过蠕变实验对热塑性聚氨酯(TPU)样品粘弹性特性进行的实验表征。实验在不同的恒温水平(15、25和35 ∘C)、三种不同的拉伸应力水平(0.3、0.5和0.7 MPa)以及不同的物理吸附水含量下进行,从而能够:(i)研究蠕变参数的温度依赖性,以及(ii)评估其行为是否确实为粘弹性。通过将原始样品暴露在相对湿度为0至80%的环境中直至质量稳定,来实现物理吸附水含量。随后立即在该特定湿度水平下进行蠕变测试。本研究的主要结果如下。在阿累尼乌斯图中很好地描述了所获得的蠕变参数的温度依赖性。关于含水量,在实验方案中观察到两种典型的材料响应,并使用以下分数型模型进行了精确建模:(i)仅为斯科特·布莱尔型(即幂律型)行为,在低含水量/低温组合下表现明显;(ii)高含水量/高温下为斯科特·布莱尔加洛姆尼茨(即对数型)组合行为。与特定环境条件(温度和相对湿度)的某些阈值相关的这种行为变化可能表明氢键断裂和重排(氨基甲酸酯氢键和物理吸附水氢键)的开始。关于短期或准瞬时行为,斯科特·布莱尔元件似乎非常合适,可能比标准弹性模型:胡克弹簧更适用。我们将斯科特·布莱尔行为与聚合物网络链的负载诱导准瞬时重排联系起来。与洛姆尼茨元件相关的二次粘弹性机制,即氢键断裂和重排,在较高温度和/或较高物理吸附水含量时起作用。在这种情况下,由于洛姆尼茨元件的特征时间数量远大于斯科特·布莱尔元件的相应值,两个本构元件的贡献得到了很好的区分。