Zhang Lingge, Li Jie, Li Jihong, Tang Hongchao, Liu Yuxue
Dept. of Oral and Maxillofacial Surgery, Zhengzhou Stomatologic Hospital, Zhengzhou 450000, China.
Dept. of Orthodontics, Zhengzhou Stomatologic Hospital, Zhengzhou 450000, China.
Hua Xi Kou Qiang Yi Xue Za Zhi. 2022 Jul 25;40(4):446-450. doi: 10.7518/hxkq.2022.04.012.
This study aimed to evaluate the clinical application value of 3D printed template-guided radiofrequency thermocoagulation combined with doxorubicin injection for the treatment of trigeminal neuralgia mandibular branch.
A total of 50 patients with primary trigeminal neuralgia mandibular branch in the hospital from January 2019 to September 2020 were randomly divided into two groups: 3D printed template-guided radiofrequency thermocoagulation combined with doxorubicin injection was used as the research group (=25), and 3D printed template guided radiofrequency thermocoagulation was used as the control group (=25). Comparative analysis of visual analogue score (VAS) was conducted before and immediately after surgery and at 1, 3, 6, and 12 months after surgery. The Brisman efficacy evaluation criteria for trigeminal neuralgia was used to evaluate the therapeutic effect of each postoperative follow-up period, and postoperative complications were observed.
The VAS immediately after surgery and at 1, 3, 6, and 12 months after surgery in the two groups was significantly lower than that before surgery, with statistical significance (<0.05). According to Brisman efficacy evaluation criteria for trigeminal neuralgia, no significant difference was found in the efficacy between the two groups at 1 and 3 months after surgery (>0.05). At 6 and 12 months postoperatively, the effectiveness of the research group was higher than that of the control group, and the differences were statistically significant (<0.05). In the research group, no recurrence occurred during the follow-up period, whereas in the control group, one, two, and four recurrences occurred 3, 6, and 12 months after surgery, respectively. No obvious complications were found in both groups.
3D printed template-guided radiofrequency thermocoagulation combined with doxorubicin injection for the treatment of trigeminal neuralgia mandibular branch could enhance the long-term curative effect and reduce the recurrence rate, thus worthy of clinical promotion and application.
本研究旨在评估3D打印模板引导下射频热凝联合阿霉素注射治疗三叉神经下颌支痛的临床应用价值。
选取2019年1月至2020年9月在本院就诊的50例原发性三叉神经下颌支痛患者,随机分为两组:采用3D打印模板引导下射频热凝联合阿霉素注射的为研究组(n = 25),采用3D打印模板引导下射频热凝的为对照组(n = 25)。分别于术前、术后即刻、术后1、3、6及12个月进行视觉模拟评分(VAS)比较分析。采用三叉神经痛的Brisman疗效评价标准评估各术后随访期的治疗效果,并观察术后并发症。
两组术后即刻及术后1、3、6、12个月的VAS均显著低于术前,差异有统计学意义(P<0.05)。根据三叉神经痛的Brisman疗效评价标准,术后1、3个月两组疗效差异无统计学意义(P>0.05)。术后6、12个月,研究组疗效高于对照组,差异有统计学意义(P<0.05)。研究组随访期间无复发,对照组术后3、6、12个月分别有1例、2例、4例复发。两组均未发现明显并发症。
3D打印模板引导下射频热凝联合阿霉素注射治疗三叉神经下颌支痛可提高远期疗效,降低复发率,值得临床推广应用。