Suppr超能文献

嗜热栖热菌在80摄氏度下于乳胶双峰共混涂料中的渗透性和反应性:一种典型的高温生物催化涂料

Permeability and reactivity of Thermotoga maritima in latex bimodal blend coatings at 80 degrees C: a model high temperature biocatalytic coating.

作者信息

Lyngberg Olav K, Solheid Chris, Charaniya Salim, Ma Yue, Thiagarajan Venkata, Scriven L E, Flickinger Michael C

机构信息

Department of Chemical Engineering and Materials Science, University of Minnesota, Minneapolis, MN 55455, USA.

出版信息

Extremophiles. 2005 Jun;9(3):197-207. doi: 10.1007/s00792-005-0434-7. Epub 2005 Mar 19.

Abstract

Thermostable polymers cast as thin, porous coatings or membranes may be useful for concentrating and stabilizing hyperthermophilic microorganisms as biocatalysts. Hydrogel matrices can be unstable above 65 degrees C. Therefore a 55-microm thick, two layer (cell coat + polymer top coat) bimodal, adhesive latex coating of partially coalesced polystyrene particles was investigated at 80 degrees C using Thermotoga maritima as a model hyperthermophile. Coating permeability (pore structure) was critical for maintaining T. maritima viability. The permeability of bimodal coatings generated from 0.8 v/v of a suspension of non-film-forming 800 nm polystyrene particles with high glass transition temperature (T(g) = 94 degrees C, 26.9% total solids) blended with 0.2 v/v of a suspension of film-forming 158 nm polyacrylate/styrene particles (T(g) approximately -5 degrees C, 40.9% total solids) with 0.3 g sucrose/g latex was measured in a KNO3 diffusion cell. Diffusivity ratio remained above 0.04 (D(eff)/D) when incubated at 80 degrees C in artificial seawater (ASW) for 5 days. KNO3 permeability was corroborated by cryogenic-SEM images of the pore structure. In contrast, the permeability of a mono-dispersed acrylate/vinyl acetate latex Rovace SF091 (T(g) approximately 10 degrees C) rapidly decreased and became impermeable after 2 days incubation in ASW at 80 degrees C. Thermotoga maritima were entrapped in these coatings at a cell density of 49 g cell wet weight/liter of coating volume, 25-fold higher than the density in liquid culture. Viable T. maritima were released from single-layer coatings at 80 degrees C but accurate measurement of the percentage of viable entrapped cells by plate counting was not successful. Metabolic activity could be measured in bilayer coatings by utilization of glucose and maltose, which was identical for latex-entrapped and suspended cells. Starch was hydrolyzed for 200 h by latex-entrapped cells due to the slow diffusion of starch through the polymer top coat compared to only 24 h by suspended T. maritima. The observed reactivity and stability of these coatings was surprising since cryo-SEM images suggested that the smaller low T(g) polyacrylate/styrene particles preferentially bound to the T. maritima toga-sheath during coat formation. This model system may be useful for concentrating, entrapment and stabilization of metabolically active hyperthermophiles at 80 degrees C.

摘要

浇铸为薄的多孔涂层或膜的热稳定聚合物,可能有助于浓缩和稳定作为生物催化剂的嗜热微生物。水凝胶基质在65摄氏度以上可能不稳定。因此,使用嗜热栖热菌作为嗜热模型,在80摄氏度下研究了由部分聚结的聚苯乙烯颗粒制成的55微米厚的两层(细胞涂层+聚合物顶涂层)双峰粘性乳胶涂层。涂层渗透性(孔结构)对于维持嗜热栖热菌的活力至关重要。在KNO3扩散池中测量了由0.8 v/v的具有高玻璃化转变温度(T(g)=94摄氏度,总固体含量26.9%)的非成膜800纳米聚苯乙烯颗粒悬浮液与0.2 v/v的成膜158纳米聚丙烯酸酯/苯乙烯颗粒(T(g)约为-5摄氏度,总固体含量40.9%)以及0.3 g蔗糖/g乳胶混合而成的双峰涂层的渗透性。当在80摄氏度的人工海水中孵育5天时,扩散率比值保持在0.04以上(D(eff)/D)。KNO3渗透性通过孔结构的低温扫描电子显微镜图像得到证实。相比之下,单分散丙烯酸酯/醋酸乙烯酯乳胶Rovace SF091(T(g)约为10摄氏度)的渗透性在80摄氏度的人工海水中孵育2天后迅速下降并变得不可渗透。嗜热栖热菌以49 g细胞湿重/升涂层体积的细胞密度被包埋在这些涂层中,比液体培养中的密度高25倍。在80摄氏度下,存活的嗜热栖热菌从单层涂层中释放出来,但通过平板计数准确测量包埋细胞的存活百分比未成功。双层涂层中的代谢活性可以通过葡萄糖和麦芽糖的利用来测量,这对于乳胶包埋细胞和悬浮细胞是相同的。由于淀粉通过聚合物顶涂层的扩散缓慢,包埋在乳胶中的细胞将淀粉水解了200小时,而悬浮的嗜热栖热菌仅水解24小时。这些涂层所观察到的反应性和稳定性令人惊讶,因为低温扫描电子显微镜图像表明,在涂层形成过程中,较小的低T(g)聚丙烯酸酯/苯乙烯颗粒优先与嗜热栖热菌的鞘结合。这个模型系统可能有助于在80摄氏度下浓缩、包埋和稳定代谢活跃的嗜热菌。

文献AI研究员

20分钟写一篇综述,助力文献阅读效率提升50倍。

立即体验

用中文搜PubMed

大模型驱动的PubMed中文搜索引擎

马上搜索

文档翻译

学术文献翻译模型,支持多种主流文档格式。

立即体验