McIntosh Robert L, Anderson Vitas, McKenzie Raymond J
Telstra Research Laboratories, Clayton, Australia.
Bioelectromagnetics. 2005 Jul;26(5):377-88. doi: 10.1002/bem.20112.
The 1998 International Commission for Non-Ionising Radiation (ICNIRP) Guidelines for human exposure to radiofrequency (RF) fields contain a recommendation to assess the potential impact of metallic implants in workers exposed up to the allowable occupational field limits. This study provides an example of how numerical electromagnetic (EM) and thermal modelling can be used to determine whether scattered RF fields around metallic implants in workers exposed to allowable occupational ambient field limits will comply with the recommendations of relevant standards and guidelines. A case study is performed for plane wave exposures of a 50 mm diameter titanium cranioplasty plate, implanted around 5-6 mm under the surface of the forehead. The level of exposures was set to the ambient power flux density limits for occupational exposures specified in the 1998 ICNIRP guidelines and the current 1999 IEEE C95.1 standard over the frequency range 100-3000 MHz. Two distinct peak responses were observed. There was a resonant response for the whole implant at 200-300 MHz where the maximum dimension of the implant is around a third of the wavelength of the RF exposure. This, however, resulted in relatively low peak specific energy absorption rate (SAR) levels around the implant at the exposure limits. Between 2100-2800 MHz, a second SAR concentrating mechanism of constructive interference of the wave reflected back and forth between the air-scalp interface and the scalp-plate interface resulted in higher peak SARs that were within the allowable limits for the ICNIRP exposures, but not for the IEEE C95.1 exposures. Moreover, the IEEE peak SAR limits were also exceeded, to a lesser degree, even when the implant was not present. However, thermal modelling indicated that the peak SAR concentrations around the implant did not result in any peak temperature rise above 1 degrees C for occupational exposures recommended in the ICNIRP guidelines, and hence would not pose any significant health risk.
1998年国际非电离辐射委员会(ICNIRP)关于人类暴露于射频(RF)场的指南建议,对于暴露在允许职业场限值内的工人,应评估金属植入物的潜在影响。本研究提供了一个示例,说明如何使用数值电磁(EM)和热模型来确定暴露在允许职业环境场限值内的工人,其金属植入物周围的散射RF场是否符合相关标准和指南的建议。针对一个直径50毫米的钛颅骨成形板进行了案例研究,该板植入在前额表面下方约5 - 6毫米处。暴露水平设定为1998年ICNIRP指南和当前1999年IEEE C95.1标准中规定的职业暴露的环境功率通量密度限值,频率范围为100 - 3000兆赫。观察到两个不同的峰值响应。在200 - 300兆赫时,整个植入物出现共振响应,此时植入物的最大尺寸约为RF暴露波长的三分之一。然而,这导致在暴露限值下植入物周围的峰值比吸收率(SAR)水平相对较低。在2100 - 2800兆赫之间,空气 - 头皮界面和头皮 - 板界面之间来回反射的波的相长干涉形成了第二种SAR集中机制,导致更高的峰值SAR,这些峰值在ICNIRP暴露的允许限值内,但不在IEEE C95.1暴露的允许限值内。此外,即使没有植入物,IEEE的峰值SAR限值也在较小程度上被超过。然而,热模型表明,对于ICNIRP指南中建议的职业暴露,植入物周围的峰值SAR集中不会导致任何峰值温度升高超过1摄氏度,因此不会构成任何重大健康风险。