Degen Thomas, Jäckel Heinz
Department of Information Technology and Electrical Engeering, Swiss Federal Institute of Technology, Zurich, Switzerland.
IEEE Trans Biomed Eng. 2006 Feb;53(2):300-10. doi: 10.1109/TBME.2005.862531.
Most wired active electrodes reported so far have a gain of one and require at least three wires. This leads to stiff cables, large connectors and additional noise for the amplifier. The theoretical advantages of amplifying the signal on the electrodes right from the source has often been described, however, rarely implemented. This is because a difference in the gain of the electrodes due to component tolerances strongly limits the achievable common mode rejection ratio (CMRR). In this paper, we introduce an amplifier for bioelectric events where the major part of the amplification (40 dB) is achieved on the electrodes to minimize pick-up noise. The electrodes require only two wires of which one can be used for shielding, thus enabling smaller connecters and smoother cables. Saturation of the electrodes is prevented by a dc-offset cancelation scheme with an active range of +/- 250 mV. This error feedback simultaneously allows to measure the low frequency components down to dc. This enables the measurement of slow varying signals, e.g., the change of alertness or the depolarization before an epileptic seizure normally not visible in a standard electroencephalogram (EEG). The amplifier stage provides the necessary supply current for the electrodes and generates the error signal for the feedback loop. The amplifier generates a pseudodifferential signal where the amplified bioelectric event is present on one lead, but the common mode signal is present on both leads. Based on the pseudodifferential signal we were able to develop a new method to compensate for a difference in the gain of the active electrodes which is purely software based. The amplifier system is then characterized and the input referred noise as well as the CMRR are measured. For the prototype circuit the CMRR evaluated to 78 dB (without the driven-right-leg circuit). The applicability of the system is further demonstrated by the recording of an ECG.
迄今为止报道的大多数有线有源电极增益为1,且至少需要三根导线。这会导致电缆僵硬、连接器较大以及放大器产生额外噪声。从源头就在电极上放大信号的理论优势虽常被提及,但很少得以实现。这是因为由于元件公差导致的电极增益差异会严重限制可实现的共模抑制比(CMRR)。在本文中,我们介绍一种用于生物电事件的放大器,其中大部分放大(40 dB)在电极上实现,以尽量减少拾取噪声。这些电极仅需两根导线,其中一根可用于屏蔽,从而实现更小的连接器和更顺滑的电缆。通过有源范围为+/- 250 mV的直流偏移消除方案可防止电极饱和。这种误差反馈同时允许测量低至直流的低频分量。这使得能够测量缓慢变化的信号,例如警觉性的变化或癫痫发作前通常在标准脑电图(EEG)中不可见的去极化。放大器级为电极提供必要的电源电流,并为反馈回路生成误差信号。该放大器生成一个伪差分信号,其中放大的生物电事件出现在一根导线上,但共模信号出现在两根导线上。基于该伪差分信号,我们能够开发一种全新的方法来补偿有源电极增益的差异,该方法完全基于软件。然后对放大器系统进行表征,并测量输入参考噪声以及CMRR。对于原型电路,评估得到的CMRR为78 dB(无驱动右腿电路)。通过记录心电图进一步证明了该系统的适用性。