Ropars Mickaël, Fontaine Isabelle, Morandi Xavier, Berton Eric, Kaila Rajiv, Darnault Pierre
Laboratoire d'Anatomie et d'Organogenèse, Faculté de Médecine, Centre Hospitalier Universitaire de Rennes, 2 avenue du Professeur Léon Bernard, 35043, Rennes Cedex, France.
Surg Radiol Anat. 2010 Mar;32(3):271-6. doi: 10.1007/s00276-010-0622-8. Epub 2010 Jan 16.
The superficial branch of the radial nerve (SBRN) is potentially at risk during thumb carpometacarpal (TCM) or thumb metacarpophalangeal (TMP) joint arthroscopy. The aim of this anatomical study was to describe the different branching patterns of the SBRN and to optimize positioning of portals during TCM and TMP arthroscopy.
The SBRN was dissected in 30 forearms. Three branches of the nerve (SR1, SR2, and SR3) were recorded and distances between SBRN branches and portals used for carpometacarpal (TCM) and metacarpophalangeal (TMP) joints of the thumb arthroscopy were measured. Three main portals were used for TCM joint arthroscopy. These portals were an ulnar portal (1-U), a radial portal (1-R), and an accessory portal (D-2). A radial metacarpophalangeal (MCP-rad) and an ulnar metacarpophalangeal (MCP-uln) portal were used for TMP joint arthroscopy.
In 24 cases (80%), the 1-R portal was inserted radially (volar) to SR3 at a mean distance of 4.8 mm (0-8). In the remaining six cases (20%) when 1-R portal was inserted ulnar (dorsal) to SR3, the distance was less than 2 mm in all cases. SR3 was always far from the 1-U portal at a mean 13 mm (7-22). The D-2 portal was always close to SR2-D1 at a mean distance of 1.7 mm (0-6). The distance from SR2-D2 and D-2 portal was also inferior by 5 mm. At the level of the metacarphalangeal joint of the thumb, the MCP-rad portal was always situated dorsally and very close to SR3, at a mean distance of 1 mm (0-5). The MCP-uln portal was also situated dorsal to SR2-D1 at a mean distance of 3.7 mm (1.5-6.5).
The results of this anatomical study confirm actual reported findings about the SR2 and SR3 branches. These two branches of the SBRN are the most at risk of injury during TCM and TMP joint arthroscopy. According to our measurements, the 1-U portal is a safer portal than 1-R and D-2 portal for TCM arthroscopy and should be preferred for surgery necessitating only one portal. Concerning TMP arthroscopy, the SBRN appears less at risk of injury when using a MCP-uln portal and safer than MCP-rad which is at risk at less than 5 mm from the extensor pollicis longus tendon.
在拇指腕掌关节(TCM)或拇指掌指关节(TMP)关节镜检查过程中,桡神经浅支(SBRN)存在潜在风险。本解剖学研究的目的是描述SBRN的不同分支模式,并优化TCM和TMP关节镜检查时的切口定位。
在30条前臂上解剖SBRN。记录神经的三个分支(SR1、SR2和SR3),并测量SBRN分支与用于拇指关节镜检查的腕掌关节(TCM)和掌指关节(TMP)切口之间的距离。TCM关节镜检查使用三个主要切口。这些切口分别是尺侧切口(1-U)、桡侧切口(1-R)和辅助切口(D-2)。桡侧掌指关节(MCP-rad)和尺侧掌指关节(MCP-uln)切口用于TMP关节镜检查。
在24例(80%)中,1-R切口在桡侧(掌侧)插入至SR3,平均距离为4.8mm(0-8)。在其余6例(20%)中,当1-R切口在尺侧(背侧)插入至SR3时,所有病例的距离均小于2mm。SR3始终远离1-U切口,平均距离为13mm(7-22)。D-2切口始终靠近SR2-D1,平均距离为1.7mm(0-6)。SR2-D2与D-2切口的距离也相差5mm。在拇指掌指关节水平,MCP-rad切口始终位于背侧,且非常靠近SR3,平均距离为1mm(0-5)。MCP-uln切口也位于SR2-D1的背侧,平均距离为3.7mm(1.5-6.5)。
本解剖学研究结果证实了关于SR2和SR3分支的实际报道结果。SBRN的这两个分支在TCM和TMP关节镜检查期间最易受伤。根据我们的测量,对于TCM关节镜检查,1-U切口比1-R和D-2切口更安全,对于仅需要一个切口的手术应优先选择。关于TMP关节镜检查,使用MCP-uln切口时SBRN受伤的风险似乎较小,比MCP-rad切口更安全,后者距离拇长伸肌腱小于5mm时存在风险。