Walsh P J, Walker G M, Maggs C A, Buchanan F J
School of Mechanical and Aerospace Engineering, Queens University of Belfast, Northern Ireland, UK.
Proc Inst Mech Eng H. 2011 Jun;225(6):563-74. doi: 10.1177/0954411910396306.
Bone void fillers that can enhance biological function to augment skeletal repair have significant therapeutic potential in bone replacement surgery. This work focuses on the development of a unique microporous (0.5-10 microm) marine-derived calcium phosphate bioceramic granule. It was prepared from Corallina officinalis, a mineralized red alga, using a novel manufacturing process. This involved thermal processing, followed by a low pressure-temperature chemical synthesis reaction. The study found that the ability to maintain the unique algal morphology was dependent on the thermal processing conditions. This study investigates the effect of thermal heat treatment on the physiochemical properties of the alga. Thermogravimetric analysis was used to monitor its thermal decomposition. The resultant thermograms indicated the presence of a residual organic phase at temperatures below 500 degrees C and an irreversible solid-state phase transition from mg-rich-calcite to calcium oxide at temperatures over 850 degrees C. Algae and synthetic calcite were evaluated following heat treatment in an air-circulating furnace at temperatures ranging from 400 to 800 degrees C. The highest levels of mass loss occurred between 400-500 degrees C and 700-800 degrees C, which were attributed to the organic and carbonate decomposition respectively. The changes in mechanical strength were quantified using a simple mechanical test, which measured the bulk compressive strength of the algae. The mechanical test used may provide a useful evaluation of the compressive properties of similar bone void fillers that are in granular form. The study concluded that soak temperatures in the range of 600 to 700 degrees C provided the optimum physiochemical properties as a precursor to conversion to hydroxyapatite (HA). At these temperatures, a partial phase transition to calcium oxide occurred and the original skeletal morphology of the alga remained intact.
能够增强生物功能以促进骨骼修复的骨缺损填充材料在骨置换手术中具有巨大的治疗潜力。这项工作聚焦于开发一种独特的微孔(0.5 - 10微米)海洋来源的磷酸钙生物陶瓷颗粒。它是由钙化红藻珊瑚藻通过一种新颖的制造工艺制备而成。这一过程包括热处理,随后是低压 - 温度化学合成反应。研究发现,保持独特藻类形态的能力取决于热处理条件。本研究调查了热热处理对藻类理化性质的影响。采用热重分析来监测其热分解过程。所得热重曲线表明,在低于500摄氏度的温度下存在残余有机相,而在超过850摄氏度的温度下会发生从富镁方解石到氧化钙的不可逆固态相变。在空气循环炉中于400至800摄氏度的温度范围内对藻类和合成方解石进行热处理后进行评估。最高质量损失水平分别出现在400 - 500摄氏度和700 - 800摄氏度之间,分别归因于有机成分和碳酸盐的分解。使用简单的力学测试对力学强度变化进行量化,该测试测量藻类的整体抗压强度。所采用的力学测试可为评估类似颗粒状骨缺损填充材料的压缩性能提供有用的参考。研究得出结论,600至700摄氏度的浸泡温度作为转化为羟基磷灰石(HA)的前体可提供最佳的理化性质。在这些温度下,会发生部分向氧化钙的相变,并且藻类的原始骨骼形态保持完整。