Department of Civil and Environmental Engineering, Tufts University, 200 College Ave, 113 Anderson Hall, Medford, MA 02155, USA.
Water Res. 2012 Sep 15;46(14):4521-31. doi: 10.1016/j.watres.2012.05.036. Epub 2012 May 30.
A series of one-dimensional column experiments was conducted to examine the effects of tube length on the transport and deposition of 4-ethoxybenzoic acid functionalized multi-wall carbon nanotubes (MWCNTs) in water-saturated porous media. Aqueous MWCNTs suspensions were prepared to yield three distributions of tube lengths; 0.02-1.3 μm (short), 0.2-7.5 μm (medium), and 0.2-21.4 μm (long). Results of the column studies showed that MWCNT retention increased with increasing tube length. Nevertheless, more than 76% of the MWCNT mass delivered to the columns was detected in effluent samples under all experimental conditions, indicating that the functionalized MWCNTs were readily transported through 40-50 mesh Ottawa sand. Examination of MWCNT length distributions in the effluent samples revealed that nanotubes with lengths greater than 8 μm were preferentially deposited. In addition, measured retention profiles exhibited the greatest MWCNT deposition near the column inlet, which was most pronounced for the long MWCNTs, and decreased sharply with travel distance. Scanning electron microscope (SEM) images showed that MWCNTs were deposited on sand surfaces over the entire column length, while larger MWCNT bundles were retained at grain intersections and near the column inlet. A mathematical model based on clean bed filtration theory (CBFT) was unable to accurately simulate the measured retention profile data, even after varying the weighting function and incorporating a nonuniform attachment rate coefficient expression. Modification of the mathematical model to account for physical straining greatly improved predictions of MWCNT retention, yielding straining rate coefficients that were four orders-of-magnitude greater than corresponding attachment rate coefficients. Taken in concert, these experimental and modeling results demonstrate the potential importance of, and need to consider, particle straining and tube length distribution when describing MWCNT transport in water-saturated porous media.
进行了一系列一维柱实验,以研究管长对 4-乙氧基苯甲酸功能化多壁碳纳米管(MWCNTs)在水饱和多孔介质中传输和沉积的影响。制备了水相 MWCNT 悬浮液,以产生三种不同长度分布的管:0.02-1.3μm(短),0.2-7.5μm(中)和 0.2-21.4μm(长)。柱实验结果表明,MWCNT 保留量随管长的增加而增加。然而,在所有实验条件下,输送到柱子的 MWCNT 质量的 76%以上都在流出物样品中被检测到,这表明功能化的 MWCNTs 很容易通过 40-50 目渥太华砂传输。在流出物样品中检查 MWCNT 长度分布表明,长度大于 8μm 的纳米管优先沉积。此外,测量的保留曲线在柱子入口附近表现出最大的 MWCNT 沉积,对于长 MWCNTs 最为明显,并且随传输距离急剧下降。扫描电子显微镜(SEM)图像显示,MWCNTs 沉积在整个柱子长度上的砂表面上,而较大的 MWCNT 束则保留在颗粒交点和柱子入口附近。基于清洁床过滤理论(CBFT)的数学模型甚至在改变加权函数并包含不均匀附着速率系数表达式后,也无法准确模拟测量的保留曲线数据。该数学模型的修改,以考虑物理应变,大大提高了 MWCNT 保留的预测,产生的应变率系数比相应的附着率系数大四个数量级。这些实验和建模结果表明,在描述水饱和多孔介质中 MWCNT 传输时,需要考虑颗粒应变和管长分布,这是非常重要的。