Javadzadegan Ashkan, Yong Andy S C, Chang Michael, Ng Martin K C, Behnia Masud, Kritharides Leonard
a Faculty of Medicine and Health Sciences , Macquarie University , Sydney , Australia.
b ANZAC Research Institute , The University of Sydney , Sydney , Australia.
Comput Methods Biomech Biomed Engin. 2017 Feb;20(3):260-272. doi: 10.1080/10255842.2016.1215439. Epub 2016 Jul 28.
Abnormal haemodynamic parameters are associated with atheroma plaque progression and instability in coronary arteries. Flow recirculation, shear stress and pressure gradient are understood to be important pathogenic mediators in coronary disease. The effect of freedom of coronary artery movement on these parameters is still unknown. Fluid-structure interaction (FSI) simulations were carried out in 25 coronary artery models derived from authentic human coronaries in order to investigate the effect of degree of freedom of movement of the coronary arteries on flow recirculation, wall shear stress (WSS) and wall pressure gradient (WPG). Each FSI model had distinctive supports placed upon it. The quantitative and qualitative differences in flow recirculation, maximum wall shear stress (MWSS), areas of low wall shear stress (ALWSS) and maximum wall pressure gradient (MWPG) for each model were determined. The results showed that greater freedom of movement was associated with lower MWSS, smaller ALWSS, smaller flow recirculation zones and lower MWPG. With increasing percentage diameter stenosis (%DS), the effect of degree of freedom on flow recirculation and WSS diminished. Freedom of movement is an important variable to be considered for computational modelling of human coronary arteries, especially in the setting of mild to moderate stenosis.
3D: Three-dimensional; 3DR: Three-dimensional Reconstruction; 3D-QCA: Three-dimensional quantitative coronary angiography; ALWSS: Areas of low wall shear stress; CAD: Coronary artery disease; CFD: Computational fluid dynamics; %DS: Diameter stenosis percentage; EPCS: End point of counter-rotating streamlines; FSI: Fluid-structure interaction; IVUS: Intravascular ultrasound; LAD: Left anterior descending; MWSS: Maximum wall shear stress; SST: Shear stress transport; TAWSS: Time-averaged wall shear stress; WSS: wall shear stress; WPG: Wall pressure gradient; MWPG: Maximum wall pressure gradient; FFR: Fractional flow reserve; iFR: Instantaneous wave-free ratio.
异常的血流动力学参数与冠状动脉粥样斑块进展及不稳定性相关。血流再循环、剪应力和压力梯度被认为是冠心病重要的致病介质。冠状动脉运动自由度对这些参数的影响尚不清楚。为了研究冠状动脉运动自由度对血流再循环、壁面剪应力(WSS)和壁面压力梯度(WPG)的影响,在25个源自真实人体冠状动脉的模型中进行了流固耦合(FSI)模拟。每个FSI模型都有独特的支撑结构。确定了每个模型在血流再循环、最大壁面剪应力(MWSS)、低壁面剪应力区域(ALWSS)和最大壁面压力梯度(MWPG)方面的定量和定性差异。结果表明,更大的运动自由度与更低的MWSS、更小的ALWSS、更小的血流再循环区域和更低的MWPG相关。随着直径狭窄百分比(%DS)增加,运动自由度对血流再循环和WSS的影响减弱。运动自由度是人体冠状动脉计算建模中需要考虑的一个重要变量,尤其是在轻度至中度狭窄的情况下。
3D:三维;3DR:三维重建;3D-QCA:三维定量冠状动脉造影;ALWSS:低壁面剪应力区域;CAD:冠状动脉疾病;CFD:计算流体动力学;%DS:直径狭窄百分比;EPCS:反向流线终点;FSI:流固耦合;IVUS:血管内超声;LAD:左前降支;MWSS:最大壁面剪应力;SST:剪应力传输;TAWSS:时间平均壁面剪应力;WSS:壁面剪应力;WPG:壁面压力梯度;MWPG:最大壁面压力梯度;FFR:血流储备分数;iFR:瞬时无波比值