Particulate Fluids Processing Centre and Department of Chemical and Biomolecular Engineering, The University of Melbourne, Parkville, VIC, 3010, Australia.
Particulate Fluids Processing Centre and Department of Chemical and Biomolecular Engineering, The University of Melbourne, Parkville, VIC, 3010, Australia; The Bio21 Molecular Science and Biotechnology Institute, The University of Melbourne, Parkville, VIC, 3010, Australia.
Water Res. 2017 Oct 15;123:578-585. doi: 10.1016/j.watres.2017.06.063. Epub 2017 Jun 23.
Filamentous bacteria can impact on the physical properties of flocs in the activated sludge process assisting solid-liquid separation or inducing problems when bacteria are overabundant. While filamentous bacteria within the flocs are understood to increase floc tensile strength, the relationship between protruding external filaments, dewatering characteristics and floc stability is unclear. Here, a quantitative methodology was applied to determine the abundance of filamentous bacteria in activated sludge samples from four wastewater treatment plants. An automated image analysis procedure was applied to identify filaments and flocs and calculate the length of the protruding filamentous bacteria (PFB) relative to the floc size. The correlation between PFB and floc behavior was then assessed. Increased filament abundance was found to increase interphase drag on the settling flocs, as quantified by the hindered settling function. Additionally, increased filament abundance was correlated with a lower gel point concentration leading to poorer sludge compactability. The floc strength factor, defined as the relative change in floc size upon shearing, correlated positively with filament abundance. This influence of external protruding filamentous bacteria on floc stability is consistent with the filamentous backbone theory, where filamentous bacteria within flocs increase floc resistance to shear-induced breakup. A qualitative correlation was also observed between protruding and internal filamentous structure. This study confirms that filamentous bacteria are necessary to enhance floc stability but if excessively abundant will adversely affect solid-liquid separation. The tools developed here will allow quantitative analysis of filament abundance, which is an improvement on current qualitative methods and the improved method could be used to assist and optimize the operation of waste water treatment plants.
丝状菌会影响活性污泥工艺中絮体的物理性质,帮助固液分离,或者在细菌过多时引发问题。虽然絮体中的丝状菌被认为会增加絮体的拉伸强度,但突出的外生丝状菌、脱水特性和絮体稳定性之间的关系尚不清楚。在这里,应用了一种定量方法来确定来自四个污水处理厂的活性污泥样品中丝状菌的丰度。应用自动化图像分析程序来识别丝状菌和絮体,并计算相对于絮体大小的突出丝状菌(PFB)的长度。然后评估 PFB 与絮体行为之间的相关性。研究发现,丝状菌丰度的增加会增加沉降絮体的相间阻力,这可以通过受阻沉降函数来定量。此外,丝状菌丰度的增加与较低的凝胶点浓度相关,从而导致较差的污泥可压缩性。定义为剪切后絮体尺寸相对变化的絮体强度因子与丝状菌丰度呈正相关。这种对外生突出丝状菌对絮体稳定性的影响与丝状菌骨架理论一致,即在絮体中的丝状菌增加了絮体对剪切引起的破裂的抵抗力。还观察到突出的和内部丝状结构之间存在定性相关性。这项研究证实,丝状菌是增强絮体稳定性所必需的,但如果过量存在,会对固液分离产生不利影响。这里开发的工具将允许对丝状菌丰度进行定量分析,这是对当前定性方法的改进,改进后的方法可用于协助和优化污水处理厂的运行。