Indiana Hand to Shoulder Center, Indianapolis, IN.
Indiana Hand to Shoulder Center, Indianapolis, IN.
J Hand Surg Am. 2020 Jul;45(7):660.e1-660.e4. doi: 10.1016/j.jhsa.2019.12.003. Epub 2020 Feb 21.
Thumb carpometacarpal (CMC) joint arthroplasty is one of the most commonly performed surgeries by hand surgeons. A large portion of these patients also have scaphotrapezoidal (ST) arthritis in addition to CMC arthritis. The purposes of this study were to quantify the amount of transverse trapezoid resection necessary to prevent ST impingement and to compare an oblique with a transverse osteotomy of the trapezoid.
A total of 9 cadaveric specimens were used and were randomly placed into 2 groups. Group 1 had sequential transverse osteotomies and the space between the scaphoid and trapezoid was measured in various wrist positions. Group 2 had oblique osteotomies and the ST distance was measured in multiple wrist positions.
In group 1, there was no contact between the scaphoid and trapezoid in neutral wrist position after any resection. The half and two-thirds transverse osteotomies did not have contact at 20° radial deviation (RD) and 30° wrist flexion (WF). In 1 of the 5 specimens, there was contact at one-third resection in either isolated RD or WF. In 3 specimens, there was contact at one-third resection with 20° of radial deviation combined with 30° WF. In group 2, there was no contact in any specimen in any wrist position tested. At neutral, there was 3.7 mm of space between the scaphoid and trapezoid measured at the radial side. In 20° RD and 0° WF, an average space remaining was 2.8 mm. In 0° RD and 30° WF, there was an average space of 2.3 mm remaining. At 20° RD and 30° WF, there was an average space remaining of 1.8 mm. At the extreme of RD and WF, there was an average space remaining of 1.4 mm.
An oblique osteotomy of the trapezoid did not have any ST contact in 20° RD and 30° WF. The transverse osteotomies had contact with only one-third resection. Therefore, if a transverse osteotomy of the trapezoid is performed, more than one-third of the bone should be resected to minimize the risk for bony impingement in positions of WF, RD, or both.
In ST arthritis, an oblique osteotomy of the trapezoid may prevent impingement while allowing for less overall bony resection compared with a transverse osteotomy.
拇指腕掌(CMC)关节成形术是手外科医生最常进行的手术之一。这些患者中有很大一部分除了 CMC 关节炎外,还有舟月(ST)关节炎。本研究的目的是量化切除横梯形所必需的量,以防止 ST 撞击,并比较梯形的斜与横切开术。
总共使用了 9 个尸体标本,并随机分为 2 组。第 1 组进行连续的横切开术,在各种腕关节位置测量舟骨和梯形之间的空间。第 2 组进行斜切开术,并在多个腕关节位置测量 ST 距离。
在第 1 组中,中立位手腕位置的任何切除后,舟骨和梯形之间没有接触。半切和三分之二横切开术在 20°桡偏(RD)和 30°腕屈(WF)时没有接触。在 5 个标本中的 1 个标本中,在单独 RD 或 WF 中,三分之一的切除有接触。在 3 个标本中,在三分之一的切除与 20°的桡偏加 30°的 WF 相结合时,有接触。在第 2 组中,在任何测试的腕关节位置的任何标本中均无接触。在中立位,桡侧测量的舟骨和梯形之间有 3.7 毫米的间隙。在 20°RD 和 0°WF 时,平均剩余空间为 2.8 毫米。在 0°RD 和 30°WF 时,平均剩余空间为 2.3 毫米。在 20°RD 和 30°WF 时,平均剩余空间为 1.8 毫米。在 RD 和 WF 的极限处,平均剩余空间为 1.4 毫米。
斜梯形切开术在 20°RD 和 30°WF 时没有任何 ST 接触。横切开术仅在三分之一的切除时有接触。因此,如果进行梯形的横切开术,则应切除超过三分之一的骨,以最大程度地降低 WF、RD 或两者位置的骨撞击风险。
在 ST 关节炎中,与横切开术相比,斜梯形切开术可能会防止撞击,同时允许进行更少的整体骨切除。