Institute of Ceramic Technology (ITC-AICE), University Jaume I, Campus Universitario Riu Sec, Av. Vicent Sos Baynat s/n, 12006 Castellón, Spain.
Institute of Environmental Assessment and Water Research (IDAEA-CSIC), C/Jordi Girona 18, 08034 Barcelona, Spain.
Int J Environ Res Public Health. 2022 Aug 5;19(15):9652. doi: 10.3390/ijerph19159652.
A sampling methodology and a mathematical data treatment were developed that enable to determine not only total suspended particulates (TSP) emitted at channeled sources but also the PM, PM, and PM mass fractions (w, w, and w) and emission factors (E.F.), using a seven-stage cascade impactor. Moreover, a chemical analysis was performed to identify the elements present in these emissions. The proposed methodology was applied to different stages of the ceramic process, including ambient temperature (milling, shaping, glazing) and medium-high-temperature (spray-drying, drying, firing, and frit melting) stages. In total, more than 100 measurements were performed (pilot scale and industrial scale), which leads to a measurement time of 1500 h. Related to the mass fractions, in general, the mean values of w after the fabric filters operated at high performance are high and with little dispersion (75-85%), and it is also observed that they are practically independent of the stage considered, i.e., they are not significantly dependent on the initial PSD of the stream to be treated. In the case of the fine fraction w, the behavior is more complex (w: 30-60%), probably because the only variable is not the cleaning system, but also the nature of the processed material. Regarding abatement measures, the use of high-efficiency cleaning systems considerably reduces the emission factors obtained for fractions PM, PM, and PM. In reference to chemical analysis, the presence of ZrO and Ni in the spray-drying and pressing stages, the significant concentration of ZrO in the glazing stage, the presence of Pb, As, and Zn in the firing stage, and the presence of Zn, Pb, Cd, and As compounds in the frits manufacturing should all be highlighted. Nevertheless, it should be pointed out that the use of some compounds, such as cadmium and lead, has been very limited in the last years and, therefore, presumably, the presence of these elements in the emissions should have been also reduced in the same way.
开发了一种采样方法和数学数据处理方法,使用七阶冲击式采样器不仅可以确定通道源排放的总悬浮颗粒物(TSP),还可以确定 PM、PM 和 PM 质量分数(w、w 和 w)和排放因子(E.F.)。此外,还进行了化学分析以确定这些排放物中存在的元素。所提出的方法应用于陶瓷工艺的不同阶段,包括环境温度(研磨、成型、上釉)和中高温(喷雾干燥、干燥、烧制和玻璃化)阶段。总共进行了 100 多次以上的测量(中试和工业规模),这导致了 1500 小时的测量时间。关于质量分数,一般来说,在高性能运行后织物过滤器的 w 的平均值较高且分散性较小(75-85%),并且还观察到它们实际上与所考虑的阶段无关,即它们与待处理流的初始 PSD 没有显著的依赖性。对于细分数 w,行为更为复杂(w:30-60%),可能是因为唯一的变量不是清洁系统,而是处理材料的性质。关于减排措施,使用高效清洁系统可大大降低 PM、PM 和 PM 分数的排放因子。关于化学分析,在喷雾干燥和压制阶段存在 ZrO 和 Ni,在上釉阶段 ZrO 的浓度显著,在烧制阶段存在 Pb、As 和 Zn,以及在玻璃化阶段制造的玻璃中存在 Zn、Pb、Cd 和 As 化合物,都应该突出强调。然而,应该指出的是,在过去几年中,一些化合物的使用,如镉和铅,已经非常有限,因此,这些元素在排放物中的存在也应该以同样的方式减少。