Department of Orthopaedics, Phramongkutklao Hospital and College of Medicine, Bangkok, Thailand.
J Hand Surg Asian Pac Vol. 2022 Oct;27(5):864-873. doi: 10.1142/S2424835522500849.
Most radial head prostheses were designed in Western countries based on the anatomical characteristics of Western populations. We hypothesised that these prostheses are too large for below-average height Thai women. The objective of this study is to evaluate the anthropometric parameters of the proximal radius in such a population and its correlation with commercially available prostheses. Dominant elbows of 124 Thai women whose height was <155 cm were studied. Using the standard anteroposterior and lateral radiographic images, the head diameter and thickness, the distance between the articular surface and radial tuberosity, the narrowest intra-medullary canal diameter and the narrowest outer diameter of the radial neck were measured. Correlations between body height and each radiographic parameter were assessed using the Pearson correlation coefficient (PCC). The specifications of the commercial metallic radial head implants were reviewed and used to evaluate the relevant radiographic parameters. Mean of the minimum and maximum head diameter was 18.54 ± 1.11 mm and 19.13 ± 1.17 mm, respectively; the thickness was 7.43 ± 0.69 mm, the distance between the articular surface and tuberosity was 19.05 ± 1.45 mm, the intra-medullary canal diameter was 7.63 ± 1.2 mm and the outer diameter of the radial neck was 11.13 ± 1.26 mm. There is a poor correlation between the participant's height and each parameter (PCC ≤ 0.50). In 24.2% of the participants, the smallest size of prosthetic designs with a head diameter of 20 mm is larger than +2 mm in reference to minor diameter. The minimum prosthetic head thickness is greater than the average value of the participants in 12 out of 15 designs. One participant has an outer neck diameter smaller than the smallest stem diameter of three designs. Surgeons must be aware that commercially available radial head replacement implants may be too large for below-average height Thai women. Level IV (Prognostic).
大多数桡骨小头假体是基于西方人群的解剖学特征在西方国家设计的。我们假设这些假体对于身高低于平均水平的泰国女性来说太大了。本研究的目的是评估该人群桡骨近端的人体测量参数及其与市售假体的相关性。 研究了 124 名身高<155cm 的泰国女性的优势肘。使用标准前后位和侧位 X 线片,测量桡骨小头的头直径和厚度、关节面与桡骨粗隆之间的距离、最小髓内管直径和桡骨颈最窄外径。使用 Pearson 相关系数(PCC)评估身高与每个影像学参数之间的相关性。审查了商业金属桡骨小头植入物的规格,并用于评估相关影像学参数。 最小和最大头直径的平均值分别为 18.54 ± 1.11mm 和 19.13 ± 1.17mm;厚度为 7.43 ± 0.69mm,关节面与粗隆之间的距离为 19.05 ± 1.45mm,髓内管直径为 7.63 ± 1.2mm,桡骨颈外径为 11.13 ± 1.26mm。参与者的身高与每个参数之间相关性差(PCC ≤ 0.50)。在 24.2%的参与者中,头直径为 20mm 的最小假体设计比参考小直径大+2mm。在 15 个设计中有 12 个的最小假体头厚度大于参与者的平均值。一名参与者的外径小于三个设计中最小的柄直径。 外科医生必须意识到,市售的桡骨小头置换植入物对于身高低于平均水平的泰国女性来说可能太大了。 四级(预后)。