Suppr超能文献

无射线支持下和有射线支持下以及根据医生经验对比托槽轴向定位准确性的三维研究。

Comparison of the accuracy of bracket axial positioning with and without radiographic support and according to practitioner experience: A three-dimensional study.

机构信息

Department of Orthodontics and Dento-facial Orthopedics, Faculty of Dental Medicine, Saint Joseph University of Beirut, Beirut, Lebanon.

Department of Orthodontics and Dento-facial Orthopedics, Faculty of Dental Medicine, Saint Joseph University of Beirut, Beirut, Lebanon.

出版信息

J World Fed Orthod. 2024 Oct;13(5):199-210. doi: 10.1016/j.ejwf.2024.03.007. Epub 2024 May 13.

Abstract

INTRODUCTION

Accurate bracket positioning remains challenging. To avoid angulation errors, some recommend examining the panoramic radiograph during bonding. However, it can cause distortions. Cone-beam computed tomography (CBCT) provides a more precise panoramic reconstruction but with higher radiation doses. The main objective of this study is to compare the accuracy of axial positioning between direct bonding without radiography, with conventional panoramic radiograph, and with panoramic reconstruction from CBCT. The secondary objectives are to evaluate positioning accuracy of each tooth and to assess the influence of practitioner level of experience.

METHODS

Thirty practitioners, divided into two groups based on their experience performed direct bonding on a model thrice: without radiography, then with the conventional panoramic radiograph, then with the panoramic reconstruction from CBCT. Models were scanned, and angulation errors were measured using OrthoAnalyzer. Values were compared using the Friedman's test followed by the Bonferroni correction for multiple comparisons (P-value = 0.05).

RESULTS

For the low level of experience group, angulation errors were significantly greater than the accepted limit without radiographic reference, and significantly lower with CBCT reconstruction. For the high level of experience group, angulation errors were significantly lower than the accepted limit for the three bonding methods. For every tooth, using the panoramic reconstruction from CBCT as a reference, was the most accurate method, regardless of the level of experience. More experienced practitioners made fewer errors for the three methods.

CONCLUSIONS

Panoramic reconstruction from CBCT is the most accurate method to limit angulation errors during direct bonding. Conventional panoramic radiography remains a reliable tool if used with caution. Bonding without any radiographic reference should be avoided especially for less experienced practitioners.

摘要

简介

准确放置托槽仍然具有挑战性。为了避免角度误差,一些人建议在粘结时检查全景片。然而,这可能会导致失真。锥形束 CT(CBCT)提供了更精确的全景重建,但辐射剂量更高。本研究的主要目的是比较直接粘结时不拍摄射线片、常规全景片和 CBCT 全景重建的轴向定位准确性。次要目的是评估每颗牙的定位准确性,并评估医生经验水平的影响。

方法

30 名医生根据经验分为两组,在模型上进行了三次直接粘结:不拍摄射线片、常规全景片和 CBCT 全景重建。模型被扫描,使用 OrthoAnalyzer 测量角度误差。使用 Friedman 检验比较数值,然后使用 Bonferroni 校正进行多重比较(P 值=0.05)。

结果

对于经验水平较低的组,无射线参考时的角度误差明显大于可接受范围,使用 CBCT 重建时明显低于可接受范围。对于经验水平较高的组,三种粘结方法的角度误差均明显低于可接受范围。对于每颗牙,使用 CBCT 全景重建作为参考是最准确的方法,无论经验水平如何。经验更丰富的医生在三种方法中的错误更少。

结论

CBCT 全景重建是限制直接粘结时角度误差的最准确方法。如果谨慎使用,常规全景片仍然是一种可靠的工具。特别是对于经验较少的医生,应避免在无任何射线参考的情况下进行粘结。

文献检索

告别复杂PubMed语法,用中文像聊天一样搜索,搜遍4000万医学文献。AI智能推荐,让科研检索更轻松。

立即免费搜索

文件翻译

保留排版,准确专业,支持PDF/Word/PPT等文件格式,支持 12+语言互译。

免费翻译文档

深度研究

AI帮你快速写综述,25分钟生成高质量综述,智能提取关键信息,辅助科研写作。

立即免费体验