Ronnett G V, Tennekoon G, Knutson V P, Lane M D
J Biol Chem. 1983 Jan 10;258(1):283-90.
The heavy isotope density shift method, in combination with a procedure for labeling cell surface insulin receptors, was used to determine the rate of transit of receptor to the cell surface from their site of synthesis and to follow the net rate of receptor removal from the plasma membrane in 3T3-L1 adipocytes. To label surface receptors, 125I-insulin was bound to cells at 4 degrees C and then covalently cross-linked to the receptors with disuccinimidyl suberate. The identity of the surface-labeled product as insulin receptor was established by immunoprecipitation with antireceptor antibody and sodium dodecyl sulfate-polyacrylamide gel electrophoresis. Fully differentiated 3T3-L1 adipocytes were shifted to medium containing heavy (greater than 95% 15N, 13C and 2H) amino acids. The rates of appearance of newly synthesized heavy receptor at the cell surface and the loss of previously synthesized light receptor from the cell surface were followed by resolving labeled heavy and light surface receptors in CsCl density gradients and quantitating labeled receptor subunits by gel electrophoresis. It was shown that 2.5-3.0 h are required for newly synthesized insulin receptor to reach and become functional in the plasma membrane. Insulin-induced down-regulation of cellular insulin receptor level had no effect on the time required for the newly synthesized receptors to reach the cell surface. Down-regulation, however, increased the first order rate constants for the inactivation of cell surface insulin receptors from 0.046 to 0.10 h-1. The fact that the rate constants for inactivation of cell surface and total cellular insulin receptors were identical in the up-regulated state (0.046 and 0.044 h-1, respectively) or in the down-regulated state (0.10 and 0.096 h-1, respectively) suggests that the rate-limiting step in the receptor inactivation pathway occurs at the cell surface.
重同位素密度转移法与一种标记细胞表面胰岛素受体的方法相结合,用于确定受体从其合成位点转运到细胞表面的速率,并追踪3T3-L1脂肪细胞中受体从质膜上清除的净速率。为了标记表面受体,将125I-胰岛素在4℃下与细胞结合,然后用辛二酸二琥珀酰亚胺酯将其与受体共价交联。通过用抗受体抗体进行免疫沉淀和十二烷基硫酸钠-聚丙烯酰胺凝胶电泳,确定表面标记产物为胰岛素受体。将完全分化的3T3-L1脂肪细胞转移到含有重(大于95% 15N、13C和2H)氨基酸的培养基中。通过在CsCl密度梯度中分离标记的重、轻表面受体,并通过凝胶电泳对标记的受体亚基进行定量,追踪新合成的重受体在细胞表面的出现速率以及先前合成的轻受体从细胞表面的丢失速率。结果表明,新合成的胰岛素受体需要2.5 - 3.0小时才能到达质膜并在其中发挥功能。胰岛素诱导的细胞胰岛素受体水平下调对新合成的受体到达细胞表面所需的时间没有影响。然而,下调增加了细胞表面胰岛素受体失活的一级速率常数,从0.046增加到0.10 h-1。在上调状态(分别为0.046和0.044 h-1)或下调状态(分别为0.10和0.096 h-1)下,细胞表面和总细胞胰岛素受体失活的速率常数相同,这一事实表明受体失活途径中的限速步骤发生在细胞表面。