Bhidayasiri Roongroj, Bronstein Jeff M, Sinha Shantanu, Krahl Scott E, Ahn Sinyeob, Behnke Eric J, Cohen Mark S, Frysinger Robert, Shellock Frank G
Department of Neurology, UCLA Medical Center and Geffen School of Medicine at UCLA, Los Angeles, CA 90095, USA.
Magn Reson Imaging. 2005 May;23(4):549-55. doi: 10.1016/j.mri.2005.02.007.
Deep brain stimulation (DBS) is used increasingly in the field of movement disorders. The implanted electrodes create not only a prior risk to patient safety during MRI, but also a unique opportunity in the collection of functional MRI data conditioned by direct neural stimulation. We evaluated MRI-related heating for bilateral neurostimulation systems used for DBS with an emphasis on assessing clinically relevant imaging parameters. Magnetic resonance imaging was performed using transmit body radiofrequency (RF) coil and receive-only head RF coil at various specific absorption rates (SARs) of RF power. In vitro testing was performed using a gel-filled phantom with temperatures recorded at the electrode tips. Each DBS electrode was positioned with a single extension loop around each pulse generator and a single loop at the "head" end of the phantom. Various pulse sequences were used for MRI including fast spin-echo, echo-planar imaging, magnetization transfer contrast and gradient-echo techniques. The MRI sequences had calculated whole-body averaged SARs and local head SARs ranging from 0.1 to 1.6 W/kg and 0.1 to 3.2 W/kg, respectively. Temperature elevations of less than 1.0 degrees C were found with the fast spin-echo, magnetization transfer contrast, gradient-echo and echo-planar clinical imaging sequences. Using the highest SAR levels, whole-body averaged, 1.6 W/kg, local exposed-body, 3.2 W/kg, and local head, 2.9 W/kg, the temperature increase was 2.1 degrees C. These results showed that temperature elevations associated with clinical sequences were within an acceptable physiologically safe range for the MR conditions used in this evaluation, especially for the use of relatively low SAR levels. Notably, these findings are highly specific to the neurostimulation systems, device positioning technique, MR system and imaging conditions used in this investigation.
深部脑刺激(DBS)在运动障碍领域的应用越来越广泛。植入电极不仅在磁共振成像(MRI)期间给患者安全带来先前风险,而且在通过直接神经刺激获取功能性MRI数据方面提供了独特机会。我们评估了用于DBS的双侧神经刺激系统与MRI相关的发热情况,重点是评估临床相关的成像参数。使用发射体射频(RF)线圈和仅接收头部RF线圈在不同的RF功率比吸收率(SARs)下进行磁共振成像。体外测试使用填充凝胶的体模,在电极尖端记录温度。每个DBS电极在每个脉冲发生器周围有一个单延伸环,并在体模的“头部”端有一个单环。用于MRI的各种脉冲序列包括快速自旋回波、回波平面成像、磁化传递对比和梯度回波技术。这些MRI序列计算出的全身平均SARs和局部头部SARs分别为0.1至1.6W/kg和0.1至3.2W/kg。在快速自旋回波、磁化传递对比、梯度回波和回波平面临床成像序列中发现温度升高小于1.0摄氏度。使用最高的SAR水平,全身平均为1.6W/kg,局部暴露身体为3.2W/kg,局部头部为2.9W/kg,温度升高为2.1摄氏度。这些结果表明,与临床序列相关的温度升高在本次评估所使用的MR条件下生理安全的可接受范围内,特别是对于使用相对较低的SAR水平。值得注意的是,这些发现对于本研究中使用的神经刺激系统、设备定位技术、MR系统和成像条件具有高度特异性。