Barrance Peter J, Williams Glenn N, Novotny John E, Buchanan Thomas S
Center for Biomedical Engineering Research, Department of Mechanical Engineering, 126 Spencer Laboratories, University of Delaware, Newark, DE 19716, USA.
J Biomech Eng. 2005 Oct;127(5):829-37. doi: 10.1115/1.1992524.
A new method is presented for measuring joint kinematics by optimally matching modeled trajectories of geometric surface models of bones with cine phase contrast (cine-PC) magnetic resonance imaging data. The incorporation of the geometric bone models (GBMs) allows computation of kinematics based on coordinate systems placed relative to full 3-D anatomy, as well as quantification of changes in articular contact locations and relative velocities during dynamic motion. These capabilities are additional to those of cine-PC based techniques that have been used previously to measure joint kinematics during activity. Cine-PC magnitude and velocity data are collected on a fixed image plane prescribed through a repetitively moved skeletal joint. The intersection of each GBM with a simulated image plane is calculated as the model moves along a computed trajectory, and cine-PC velocity data are sampled from the regions of the velocity images within the area of this intersection. From the sampled velocity data, the instantaneous linear and angular velocities of a coordinate system fixed to the GBM are estimated, and integration of the linear and angular velocities is used to predict updated trajectories. A moving validation phantom that produces motions and velocity data similar to those observed in an experiment on human knee kinematics was designed. This phantom was used to assess cine-PC rigid body tracking performance by comparing the kinematics of the phantom measured by this method to similar measurements made using a magnetic tracking system. Average differences between the two methods were measured as 2.82 mm rms for anterior/posterior tibial position, and 2.63 deg rms for axial rotation. An intertrial repeatability study of human knee kinematics using the new method produced rms differences in anterior/posterior tibial position and axial rotation of 1.44 mm and 2.35 deg. The performance of the method is concluded to be sufficient for the effective study of kinematic changes caused to knees by soft tissue injuries.
本文提出了一种新方法,通过将骨骼几何表面模型的模拟轨迹与电影相位对比(cine-PC)磁共振成像数据进行最佳匹配来测量关节运动学。几何骨模型(GBM)的引入使得能够基于相对于完整三维解剖结构放置的坐标系来计算运动学,以及在动态运动过程中量化关节接触位置和相对速度的变化。这些功能是以前用于在活动期间测量关节运动学的基于cine-PC的技术所不具备的。cine-PC幅度和速度数据是在通过重复移动的骨骼关节规定的固定图像平面上收集的。随着模型沿着计算轨迹移动,计算每个GBM与模拟图像平面的交点,并从该交点区域内的速度图像区域中采样cine-PC速度数据。根据采样的速度数据,估计固定到GBM的坐标系的瞬时线性和角速度,并使用线性和角速度的积分来预测更新的轨迹。设计了一个移动验证体模,其产生的运动和速度数据与在人体膝关节运动学实验中观察到的数据相似。通过将此方法测量的体模运动学与使用磁跟踪系统进行的类似测量进行比较,该体模用于评估cine-PC刚体跟踪性能。两种方法之间的平均差异在前/后胫骨位置测量为均方根值2.82毫米,在轴向旋转测量为均方根值2.63度。使用新方法对人体膝关节运动学进行的试验间重复性研究在前/后胫骨位置和轴向旋转方面产生的均方根差异分别为1.44毫米和2.35度。该方法的性能被认为足以有效地研究软组织损伤对膝盖造成的运动学变化。