Suppr超能文献

纤维素在NaOH/尿素水溶液中的独特凝胶化行为。

Unique gelation behavior of cellulose in NaOH/urea aqueous solution.

作者信息

Cai Jie, Zhang Lina

机构信息

Department of Chemistry, and Center of Nanoscience and Nanotechnology, Wuhan University, Wuhan 430072, China.

出版信息

Biomacromolecules. 2006 Jan;7(1):183-9. doi: 10.1021/bm0505585.

Abstract

A transparent cellulose solution was prepared by mixing 7 wt % NaOH with 12 wt % urea aqueous solution which was precooled to below -10 degrees C and which was able to rapidly dissolve cellulose at ambient temperature. The rheological properties and behavior of the gel-formed cellulose solution were investigated by using dynamic viscoelastic measurement. The effects of temperature, time, cellulose molecular weight, and concentrations on both the shear storage modulus (G') and the loss modulus (G") were analyzed. The cellulose solution having a viscosity-average molecular weight (M(eta)) of 11.4 x 10(4) had its sol-gel transition temperature decreased from 60.3 to 30.5 degrees C with an increase of its concentration from 3 to 5 wt %. The gelation temperature of a 4 wt % cellulose solution dropped from 59.4 to 30.5 degrees C as the M(eta) value was increased from 4.5 x 10(4) to 11.4 x 10(4). Interestingly, at either higher temperature (above 30 degrees C), or lower temperature (below -3 degrees C), or for longer gelation time, gels could form in the cellulose solutions. However, the cellulose solution remains a liquid state for a long time at the temperature range from 0 to 5 degrees C. For the first time, we revealed an irreversible gelation in the cellulose solution system. The gel having been formed did not dissolve even when cooled to the temperature of -10 degrees C, at which it was dissolved previously. Therefore, this indicates that either heating or cooling treatment could not break such stable gels. A high apparent activation energy (E(a)) of the cellulose solution below 0 degrees C was obtained and was used to explain the gel formation under the cooling process.

摘要

通过将7 wt%的NaOH与12 wt%的尿素水溶液混合制备透明纤维素溶液,该尿素水溶液预先冷却至-10℃以下,能够在室温下快速溶解纤维素。采用动态粘弹性测量研究了凝胶状纤维素溶液的流变性质和行为。分析了温度、时间、纤维素分子量和浓度对剪切储能模量(G')和损耗模量(G")的影响。粘度平均分子量(M(η))为11.4×10⁴的纤维素溶液,其浓度从3 wt%增加到5 wt%时,溶胶-凝胶转变温度从60.3℃降至30.5℃。当M(η)值从4.5×10⁴增加到11.4×10⁴时,4 wt%纤维素溶液的凝胶化温度从59.4℃降至30.5℃。有趣的是,在较高温度(高于30℃)、较低温度(低于-3℃)或较长凝胶化时间下,纤维素溶液中均可形成凝胶。然而,纤维素溶液在0至5℃的温度范围内长时间保持液态。我们首次揭示了纤维素溶液体系中存在不可逆凝胶化现象。形成的凝胶即使冷却至-10℃(其先前溶解的温度)也不会溶解。因此,这表明加热或冷却处理均无法破坏这种稳定的凝胶。获得了0℃以下纤维素溶液的高表观活化能(E(a)),并用于解释冷却过程中的凝胶形成。

文献AI研究员

20分钟写一篇综述,助力文献阅读效率提升50倍。

立即体验

用中文搜PubMed

大模型驱动的PubMed中文搜索引擎

马上搜索

文档翻译

学术文献翻译模型,支持多种主流文档格式。

立即体验