Achilli Antonio, Tura Flavio, Euwe Egon
Unit of Oral Pathology and Medicine, University of Milan, Milan Italy.
J Prosthet Dent. 2007 Jun;97(6 Suppl):S52-8. doi: 10.1016/S0022-3913(07)60008-0.
While immediate loading in the interforaminal area of the mandible is a documented procedure, there are limited scientific data for immediate/early loading in premolar and molar areas where less bone density is often found and functional loading is high.
The purpose of this study was to evaluate if there is a difference between immediate and early loading in premolar and molar areas of the mandible and maxilla and compare data to historic data.
Fifty-one patients received 120 tapered implants in premolar and molar areas of the mandible and maxilla, for a total of 54 short-span (2 to 4 units) fixed partial dentures. Patients with noncontrolled diseases, periodontal pathology, bruxism, and heavy smokers (more than 10 cigarettes a day) were excluded. Patients were divided into 2 groups, with placement of provisional fixed partial prostheses occurring within 24 hours (n=33) or 6 weeks (n=21) after implant surgery. The provisional prostheses had narrow, flat occlusal surfaces to reduce lateral contacts. Surgery was performed with flap elevation, a surgical guide was used, and sites with bone with lower density were underprepared. Implant insertion torque values were between 35 and 45 Ncm. After 6 months, definitive metal-ceramic prostheses were placed. Patients were monitored clinically and radiographically for marginal bone remodeling at baseline, and 3, 6, and 12 months after loading. All patients were followed for 1 year. Data were analyzed with descriptive statistics.
No implant failure occurred. Mean marginal bone resorption (SD) was 1.24 (0.88) mm for the immediate loading group and 1.19 (1.01) mm for the early loading group after 1 year.
The preliminary results demonstrate that if accurate surgical and prosthetic protocols are followed, immediate and early function are predictable and safe approaches even in premolar and molar areas with low bone density.
虽然在下颌骨椎间孔区域进行即刻加载是一种有文献记载的操作,但在前磨牙和磨牙区域进行即刻/早期加载的科学数据有限,这些区域通常骨密度较低且功能负荷较高。
本研究的目的是评估下颌骨和上颌骨的前磨牙和磨牙区域即刻加载与早期加载之间是否存在差异,并将数据与历史数据进行比较。
51例患者在下颌骨和上颌骨的前磨牙和磨牙区域接受了120颗锥形种植体,共制作了54个短跨度(2至4个单位)的固定局部义齿。排除患有未控制疾病、牙周病变、磨牙症和重度吸烟者(每天超过10支香烟)。患者分为2组,在种植手术后24小时内(n = 33)或6周内(n = 21)放置临时固定局部修复体。临时修复体具有狭窄、平坦的咬合面以减少侧向接触。手术采用翻瓣术,使用手术导板,对骨密度较低的部位准备不足。种植体植入扭矩值在35至45 Ncm之间。6个月后,放置最终的金属陶瓷修复体。在基线以及加载后3、6和12个月对患者进行临床和影像学监测,观察边缘骨重塑情况。所有患者随访1年。数据采用描述性统计进行分析。
未发生种植体失败。1年后,即刻加载组的平均边缘骨吸收(标准差)为±1.24(0.88)mm,早期加载组为±1.19(1.01)mm。
初步结果表明,如果遵循准确的手术和修复方案,即使在骨密度较低的前磨牙和磨牙区域,即刻和早期功能也是可预测且安全的方法。