De Cristofaro R, Di Cera E
Department of Biochemistry and Molecular Biophysics, Washington University School of Medicine, St. Louis, Missouri 63110.
J Protein Chem. 1991 Oct;10(5):455-68. doi: 10.1007/BF01025473.
A model-independent (phenomenological) characterization of the clotting curve is proposed. Three parameters are used to encapsulate the main features of the increase in absorbance observed at 350 nm due to the reaction of thrombin with fibrinogen that leads to clot formation: (1) the maximum increase in absorbance per unit time, delta Am, at the inflection point of the clotting curve; (2) the time needed to reach the maximum increase in absorbance, tm; and (3) the clotting time, tc, obtained from extrapolation of the slope at tm to the zero absorbance baseline. Clotting curves at low fibrinogen concentrations (0.125 divided by 0.250 microM), well below the Km, where thrombin amidase activity is rate-limiting with respect to the subsequent aggregation process, have been measured under a wide variety of experimental conditions, (i.e., as a function of thrombin concentration, pH and temperature) in order to explore the basic response of each parameter to changes in solution conditions. Under all conditions examined in this study we have observed that tm and tc are linked through a linear relationship that appears to be an important invariant property of the clotting curve, regardless of experimental conditions. No such clear relationship exists between delta Am and tc, with tc being associated with several possible values of delta Am and vice versa, depending upon solution conditions. It is proposed that tc is strictly dependent on thrombin amidase activity, while delta Am reflects properties of the aggregation process leading to clot formation. The clotting time shows a pH and temperature dependence that closely resembles that of Km/Vm for synthetic amide substrates. Furthermore, tc changes linearly with either the inverse thrombin concentration and the concentration of competitive inhibitors of fibrinogen binding to thrombin, as expected for the ratio Km/Vm. We show how the analysis of clotting curves obtained at different thrombin and inhibitor concentrations yields a quantitative measure of KI that is in excellent agreement with the value determined independently from steady-state measurements of thrombin amidase activity.
提出了一种与模型无关(唯象学)的凝血曲线表征方法。使用三个参数来概括由于凝血酶与纤维蛋白原反应导致凝块形成而在350nm处观察到的吸光度增加的主要特征:(1)凝血曲线拐点处单位时间内吸光度的最大增加量,ΔAm;(2)达到吸光度最大增加量所需的时间,tm;(3)凝血时间,tc,通过将tm处的斜率外推至零吸光度基线获得。在多种实验条件下(即作为凝血酶浓度、pH和温度的函数)测量了远低于Km的低纤维蛋白原浓度(0.125至0.250μM)下的凝血曲线,其中凝血酶酰胺酶活性相对于随后的聚集过程是限速的,以便探索每个参数对溶液条件变化的基本响应。在本研究中考察的所有条件下,我们观察到tm和tc通过线性关系相连,这似乎是凝血曲线的一个重要不变特性,与实验条件无关。ΔAm和tc之间不存在如此明确的关系,tc与ΔAm的几个可能值相关,反之亦然,这取决于溶液条件。有人提出tc严格依赖于凝血酶酰胺酶活性,而ΔAm反映了导致凝块形成的聚集过程的特性。凝血时间显示出与合成酰胺底物的Km/Vm相似的pH和温度依赖性。此外,正如Km/Vm的预期那样,tc随凝血酶浓度的倒数和纤维蛋白原与凝血酶结合的竞争性抑制剂浓度线性变化。我们展示了如何通过分析在不同凝血酶和抑制剂浓度下获得的凝血曲线来定量测量KI,该值与从凝血酶酰胺酶活性的稳态测量中独立确定的值非常一致。