Suppr超能文献

老年人手动轮椅推进过程中推轮合力与净肩关节力矩之间的关系。

Relationship between resultant force at the pushrim and the net shoulder joint moments during manual wheelchair propulsion in elderly persons.

作者信息

Desroches Guillaume, Aissaoui Rachid, Bourbonnais Daniel

机构信息

Laboratoire de Recherche en Imagerie et Orthopédie, CRCHUM, Hôpital Notre-Dame, Montréal, QC, Canada.

出版信息

Arch Phys Med Rehabil. 2008 Jun;89(6):1155-61. doi: 10.1016/j.apmr.2007.10.040.

Abstract

OBJECTIVE

To determine the relationship between the resultant force at the pushrim and the net shoulder joint moments during manual wheelchair propulsion in elderly persons.

DESIGN

Convenience sample.

SETTING

Motion analysis laboratory.

PARTICIPANTS

Older manual wheelchair users (N=14; age, 68.2+/-5.2y) were tested.

INTERVENTIONS

Kinematic and kinetic data were collected during manual wheelchair propulsion at a speed between 0.96 and 1.01m/s for 10 seconds and at a power output around 22.4W on a wheelchair ergometer.

MAIN OUTCOME MEASURES

Net shoulder joint moments were computed with an inverse dynamic model. The mechanical use of the forces at the pushrim and the mechanical fraction of effective force were measured during propulsion.

RESULTS

Mechanical use and mechanical fraction of effective force had a positive and significant correlation with the net internal (P<.05) and external (P<.001) shoulder rotation moment, the net flexion (P<.05), and extension (P<.001) moment in the sagittal plane, and the net flexion (P<.001) moment in the horizontal plane.

CONCLUSIONS

The results suggest that because the resultant force at the pushrim has a greater tangential component and a greater proportion of the maximal voluntary force, most of the net moments around the shoulder are higher. Thus the optimal way of propelling, from a mechanical point of view (ie, tangential), may not be advantageous for manual wheelchair users.

摘要

目的

确定老年人手动轮椅推进过程中轮辋合力与净肩关节力矩之间的关系。

设计

便利样本。

地点

运动分析实验室。

参与者

测试了老年手动轮椅使用者(N = 14;年龄,68.2±5.2岁)。

干预措施

在轮椅测力计上以0.96至1.01m/s的速度手动推进轮椅10秒,并在功率输出约22.4W的情况下收集运动学和动力学数据。

主要观察指标

使用逆动力学模型计算净肩关节力矩。在推进过程中测量轮辋处力的机械利用情况和有效力的机械占比。

结果

有效力的机械利用情况和机械占比与净内旋(P<0.05)和外旋(P<0.001)肩关节力矩、矢状面内的净屈曲(P<0.05)和伸展(P<0.001)力矩以及水平面内的净屈曲(P<0.001)力矩呈正相关且具有显著性。

结论

结果表明,由于轮辋合力具有更大的切向分量和更大比例的最大随意力,肩部周围的大多数净力矩更高。因此,从力学角度(即切向)来看,最佳的推进方式可能对手动轮椅使用者并无益处。

文献检索

告别复杂PubMed语法,用中文像聊天一样搜索,搜遍4000万医学文献。AI智能推荐,让科研检索更轻松。

立即免费搜索

文件翻译

保留排版,准确专业,支持PDF/Word/PPT等文件格式,支持 12+语言互译。

免费翻译文档

深度研究

AI帮你快速写综述,25分钟生成高质量综述,智能提取关键信息,辅助科研写作。

立即免费体验