Hangsaphuk Naraphong, Tanavalee Aree
Department of Orthopedic Surgery, Sirindhon Hospital, Bangkok, Thailand
J Med Assoc Thai. 2009 Dec;92 Suppl 6:S69-74.
In the computer assisted total knee arthroplasty (CAS-TKA), the centers of the distal femur and the proximal tibia for the sagittal mechanical axis (SMA) of both femur and tibia have unclear references. Most CAS-TKA systems define both centers following the engineer's recommendation.
To evaluate the centers of the distal femur and the proximal tibia in sagittal plane and to determine the sagittal mechanical axis (SMA) of the normal knee in relation to the Blumensaat's line and the tibial anteroposterior line.
Fifty five normal healthy knees without flexion contracture or hyperextension were enrolled. The sagittal mechanical axis (SMA) was drawn from the center of the femoral head to the most prominent dome of the talus on the long standing hip-knee-ankle radiograph in lateral view. The point that the SMA passed the Blumensaat's line of distal femur and the tibial plateau at the proximal tibia were reported as the percentage of the total length of Blumensaat's line and of the anteroposterior width of tibial plateau r respectively.
Among 55 knees included in this study, 32 knees were right side and 23 knees were left sided. Of which, there were 14 females and 41 males. Their average age was 45 years. The average BMI was 25.67. The average knee alignment in sagittal plane was 1.7 degrees. At the distal femur, the point that SMA passed the Blumensaat's line was average 13% of the total length of Blumensaat's line. There were only 22% of the 55 knees that the SMA passed at the tip of Blumensaat's line. All of SMA in 55 knees passed within the first quarter of this line. At the proximal tibia, the point that SMA passed the tibial plateau average 45% of the anteroposterior width of tibial plateau.
The center of distal femur and proximal tibia on sagittal plane are not individual consistent. Therefore, they should be evaluated preoperatively before performing the CAS TKA to prevent the incorrect bone cutting, prosthesis malposition and poor soft tissue balance in sagittal plane.
在计算机辅助全膝关节置换术(CAS - TKA)中,股骨远端和胫骨近端用于股骨和胫骨矢状机械轴(SMA)的中心参考不明确。大多数CAS - TKA系统根据工程师的建议定义这两个中心。
评估股骨远端和胫骨近端在矢状面的中心,并确定正常膝关节的矢状机械轴(SMA)与布卢门萨特线和胫骨前后线的关系。
纳入55例无屈曲挛缩或过伸的正常健康膝关节。在站立位髋 - 膝 - 踝关节侧位X线片上,从股骨头中心向距骨最突出的圆顶绘制矢状机械轴(SMA)。报告SMA通过股骨远端布卢门萨特线和胫骨近端胫骨平台的点分别占布卢门萨特线总长度和胫骨平台前后宽度的百分比。
本研究纳入的55个膝关节中,右侧32个,左侧23个。其中,女性14例,男性41例。平均年龄45岁。平均体重指数为25.67。矢状面平均膝关节对线为1.7度。在股骨远端,SMA通过布卢门萨特线的点平均为布卢门萨特线总长度的13%。55个膝关节中只有22%的SMA通过布卢门萨特线的尖端。55个膝关节的所有SMA均通过该线的第一季度内。在胫骨近端,SMA通过胫骨平台的点平均为胫骨平台前后宽度的45%。
矢状面上股骨远端和胫骨近端的中心并非个体一致。因此,在进行CAS - TKA之前应进行术前评估,以防止矢状面的骨切割错误、假体位置不当和软组织平衡不良。