Biomaterials Laboratory, Department of Chemical and Materials Engineering, University of Auckland, Auckland, New Zealand.
Osteoarthritis Cartilage. 2010 Oct;18(10):1310-8. doi: 10.1016/j.joca.2010.06.008. Epub 2010 Jul 13.
The purpose of this study was to characterize the microstructural response of healthy cartilage in a perturbed physical environment to compressive loading with a novel channel indentation device. Manipulation of the cartilage physical environment was achieved through (1) removal of the superficial tangential zone (STZ) and (2) varying the saline bathing solution concentration.
Cartilage-on-bone blocks were subjected to creep loading under a nominal stress of 4.5 MPa via an indenter consisting of two rectangular platens separated by a narrow channel relief space to create a specific region where cartilage would not be directly loaded. Each sample was fixed in its near-equilibrium deformed state, after which the cartilage microstructure was examined using differential interference contrast (DIC) optical microscopy and scanning electron microscopy (SEM). The cartilage bulge in the channel relief space was studied in detail.
STZ removal altered the indentation response at the macro- and microstructural levels. Specifically, the strain in the directly compressed regions was reduced (P=0.012) and the bulge height in the channel relief space was greater (P<0.0001) in the STZ-removed compared with the surface-intact samples. The bulge height in the STZ-removed group was always less than the preloaded cartilage thickness. There was intense shear in the non-directly-loaded regions of intact-cartilage but not in STZ-removed cartilage. Bathing solution concentration influenced only the STZ-removed group, where lower concentrations produced significantly abrupt transitions in matrix continuity between the directly compressed and adjacent non-directly-loaded cartilage (P=0.012).
This study showed that while the surface layer was important in distributing loads away from directly-loaded regions, so were other factors such as the matrix fibrillar interconnectivity, swelling potential, and tissue anisotropy.
本研究的目的是利用一种新的通道压痕装置来描述健康软骨在受扰物理环境中对压缩载荷的微观结构响应。通过(1)去除表层切线区(STZ)和(2)改变盐溶液浴浓度来实现对软骨物理环境的操作。
通过由两个由狭窄通道减压空间隔开的矩形平板组成的压头,使软骨-骨块在名义应力为 4.5 MPa 的条件下承受蠕变加载,以在特定区域内不会直接加载软骨。每个样本都被固定在其近平衡变形状态,之后使用微分干涉对比(DIC)光学显微镜和扫描电子显微镜(SEM)检查软骨微观结构。详细研究了通道减压空间中的软骨隆起。
STZ 去除改变了宏观和微观结构水平的压痕响应。具体来说,直接压缩区域的应变减小(P=0.012),并且通道减压空间中的隆起高度在 STZ 去除的样本中比表面完整的样本更大(P<0.0001)。STZ 去除组中的隆起高度始终小于预加载的软骨厚度。完整软骨的非直接加载区域存在强烈的剪切,但在 STZ 去除的软骨中不存在。浴液浓度仅影响 STZ 去除组,其中较低的浓度导致直接压缩和相邻非直接加载软骨之间的基质连续性发生明显的突然变化(P=0.012)。
本研究表明,虽然表面层对于将载荷从直接加载区域分散很重要,但其他因素如基质纤维互联、膨胀潜力和组织各向异性也很重要。