Faculty of Biomedical Engineering, Technion-Israel Institute of Technology, Haifa 32000, Israel.
Acta Biomater. 2012 May;8(5):1838-48. doi: 10.1016/j.actbio.2011.12.034. Epub 2012 Jan 13.
Cell-encapsulating hydrogels used in regenerative medicine are designed to undergo a rapid liquid-to-solid phase transition in the presence of cells and tissues so as to maximize crosslinking and minimize cell toxicity. Light-activated free-radical crosslinking (photopolymerization) is of particular interest in this regard because it can provide rapid reaction rates that result in uniform hydrogel properties with excellent temporal and spatial control features. Among the many initiator systems available for photopolymerization, only a few have been identified as suitable for cell-based hydrogel formation owing to their water solubility, crosslinking properties and non-toxic reaction conditions. In this study, three long-wave ultraviolet (UV) light-activtied photoinitiators (PIs) were comparatively tested in terms of cytotoxicity, crosslinking efficiency and crosslinking kinetics of cell-encapsulating hydrogels. The hydrogels were photopolymerized from poly(ethylene glycol) (PEG) diacrylate or PEG-fibrinogen precursors using Irgacure® PIs I2959, I184 and I651, as well as with a chemical initiator/accelerator (APS/TEMED). The study specifically evaluated the PI type, PI concentration and UV light intensity, and how these affected the mechanical properties of the hydrogel (i.e. maximum storage modulus), the crosslinking reaction times and the reaction's cytotoxicity to encapsulated cells. Only two initiators (I2959 and I184) were identified as being suitable for achieving both high cell viability and efficient crosslinking of the cell-encapsulating hydrogels during the photopolymerization reaction. Optimization of PI concentration or irradiation intensity was particularly important for achieving maximum mechanical properties; a sub-optimal choice of PI concentration or irradiation intensity resulted in a substantial reduction in hydrogel modulus. Cytocompatibility may be compromised by unnecessarily prolonging exposure to cytotoxic free radicals or inadvertently enhancing the instantaneous dose of radicals in solution, both of which are dependent on the PI type/concentration and irradiation intensity. In the absence of a radical initiator, the short exposures to long-wave UV light irradiation (up to 5 min, 20 mW cm(-2), 365 nm) did not prove to be cytotoxic to cells. Therefore, it is important to understand the relationship between PIs, light irradiation conditions and crosslinking when attempting to identify a suitable hydrogel formation process for cell encapsulating hydrogels.
用于再生医学的细胞包封水凝胶旨在在细胞和组织存在的情况下快速经历液-固相变,以最大限度地提高交联度并最小化细胞毒性。光激活自由基交联(光聚合)在这方面特别有趣,因为它可以提供快速的反应速率,从而在具有优异的时间和空间控制特性的情况下获得均匀的水凝胶性质。在可用于光聚合的许多引发剂系统中,只有少数几种由于其水溶性、交联性质和无毒反应条件而被确定为适合基于细胞的水凝胶形成的引发剂。在这项研究中,三种长波紫外线(UV)光活性光引发剂(PI)在细胞包封水凝胶的细胞毒性、交联效率和交联动力学方面进行了比较测试。使用 Irgacure® PI I2959、I184 和 I651 以及化学引发剂/加速剂(APS/TEMED)从聚乙二醇(PEG)二丙烯酸酯或 PEG-纤维蛋白原前体中光聚合水凝胶。该研究专门评估了 PI 类型、PI 浓度和 UV 光强度,以及这些因素如何影响水凝胶的机械性能(即最大存储模量)、交联反应时间以及反应对包封细胞的细胞毒性。只有两种引发剂(I2959 和 I184)被确定为适合在光聚合反应中同时实现高细胞活力和高效交联细胞包封水凝胶。PI 浓度或辐照强度的优化对于实现最大机械性能尤为重要;PI 浓度或辐照强度选择不当会导致水凝胶模量大幅降低。细胞相容性可能会因不必要地延长暴露于细胞毒性自由基或无意中增强溶液中自由基的瞬时剂量而受到损害,这两者都取决于 PI 类型/浓度和辐照强度。在不存在自由基引发剂的情况下,短时间暴露于长波 UV 光照射(长达 5 分钟,20 mW cm(-2),365nm)对细胞没有显示出细胞毒性。因此,在试图确定适合细胞包封水凝胶的水凝胶形成过程时,了解 PI、光照射条件和交联之间的关系非常重要。