W.J. Kolff Institute, Department of Biomedical Engineering, University Medical Centre Groningen, University of Groningen, P.O. Box 196, 9700 AD Groningen, The Netherlands.
Acta Biomater. 2012 Dec;8(12):4233-43. doi: 10.1016/j.actbio.2012.09.014. Epub 2012 Sep 17.
Soft hydrogels with elasticity modulus values lower than 100kPa that are tough and biodegradable are of great interest in medicine and in tissue engineering applications. We have developed a series of soft hydrogel structures from different methacrylate-functionalized triblock copolymers of poly(ethylene glycol) (PEG) with poly(trimethylene carbonate) (PTMC) by photo-crosslinking aqueous solutions of the macromonomers in 2.5 and 5wt.% colloidal dispersions of clay nanoparticles (Laponite XLG). The length of the PTMC blocks of the macromonomers and the clay content determined the physicomechanical properties of the obtained hydrogels. While an increase in the PTMC block length in the macromonomers from 0.2 to 5kg/mol resulted in a decrease in the gel content, the addition of 5wt.% Laponite nanoclay to the crosslinking solution lead to very high gel contents of the hydrogels of more than 95%. The effect of PTMC block length on the mechanical properties of the hydrogels was not as pronounced, and soft gels with a compressive modulus of less than 15kPa and toughness values of 25kJm(-3) were obtained. However, the addition of 5wt.% Laponite nanoclay to the formulations considerably increased the compressive modulus and resilience of the hydrogels; swollen nanocomposite networks with compressive modulus and toughness values of up to 67kPa and 200kJm(-3), respectively, could then be obtained. The prepared hydrogels were shown to be enzymatically degradable by cholesterol esterase and by the action of macrophages. With an increase in PTMC block length in the hydrogels, the rates of mass loss increased, while the incorporated Laponite nanoclay suppressed degradation. Nanocomposite hydrogel structures with a designed gyroid pore network architecture were prepared by stereolithography. Furthermore, in the swollen state the porous gyroid structures were mechanically stable and the pore network remained fully open and interconnected.
具有低于 100kPa 的弹性模量值、韧性和可生物降解的软水凝胶在医学和组织工程应用中具有很大的兴趣。我们已经通过光交联不同的甲基丙烯酰基官能化的聚(乙二醇)(PEG)与聚(三亚甲基碳酸酯)(PTMC)三嵌段共聚物的大分子单体的水溶液,在 2.5 和 5wt.% 的粘土纳米颗粒(Laponite XLG)胶体分散体中,开发了一系列软水凝胶结构。大分子单体中 PTMC 链段的长度和粘土含量决定了所得水凝胶的物理力学性能。随着大分子单体中 PTMC 链段长度从 0.2 增加到 5kg/mol,凝胶含量降低,而将 5wt.% 的 Laponite 纳米粘土添加到交联溶液中,导致水凝胶的凝胶含量非常高,超过 95%。PTMC 链段长度对水凝胶机械性能的影响不明显,得到的软凝胶压缩模量小于 15kPa,韧性值为 25kJm(-3)。然而,向配方中添加 5wt.% 的 Laponite 纳米粘土会显著提高水凝胶的压缩模量和弹性恢复率;然后可以获得溶胀纳米复合网络,其压缩模量和韧性值分别高达 67kPa 和 200kJm(-3)。所制备的水凝胶显示出可被胆固醇酯酶和巨噬细胞降解。随着水凝胶中 PTMC 链段长度的增加,质量损失率增加,而加入的 Laponite 纳米粘土抑制了降解。通过立体光刻法制备了具有设计的胞状孔网络结构的纳米复合水凝胶结构。此外,在溶胀状态下,多孔胞状结构在机械上是稳定的,孔网络保持完全开放和相互连接。