Suppr超能文献

使用 CT 评估非小细胞肺癌胸膜侵犯:测量肿瘤与相邻结构之间界面与最大肿瘤直径的比值。

Use of CT to evaluate pleural invasion in non-small cell lung cancer: measurement of the ratio of the interface between tumor and neighboring structures to maximum tumor diameter.

机构信息

Department of Chest, Breast and Endocrinologic Surgery and Department of Integrated Medicine, Division of Radiology and Radiation Medicine, Akita University Graduate School of Medicine, 1-1-1 Hondo Akita City 010-8543, Japan.

出版信息

Radiology. 2013 May;267(2):619-26. doi: 10.1148/radiol.12120864. Epub 2013 Jan 17.

Abstract

PURPOSE

To develop a simple noninvasive technique for evaluating pleural invasion by using routine preoperative computed tomography (CT).

MATERIALS AND METHODS

The institutional review board approved this retrospective study, and written informed consent was obtained for performing the initial and follow-up CT studies. Preoperative CT findings (169 patients with possible pleural invasion) and pathologic diagnoses after surgical resection were evaluated. The length of the interface between the primary tumor and neighboring structures (arch distance) and the maximum tumor diameter were measured on CT images, after which arch distance-to-maximum tumor diameter ratios were calculated. Receiver operating characteristic (ROC) curves were used to analyze the ratios.

RESULTS

Median arch distance-to-maximum tumor diameter ratios for pleural invasion categories (pl1, pl2, pl3) assessed by using the Union Internationale Contre le Cancer TNM staging system were as follows: pl1, 0.206 (25th-75th percentile, 0-0.486); pl2, 0.638 (25th-75th percentile, 0.385-0.830); and pl3, 1.092 (25th-75th percentile, 1.045-1.214) (P < .001 between groups). On the basis of the ROC curves, the cut-off value for invasion was an arch distance-to-maximum tumor diameter ratio of 0.9. When the ratio was greater than 0.9, the sensitivity and specificity for thoracic invasion and area under the ROC curve were 89.7%, 96.0%, and 0.976, respectively, which represents an improvement over values obtained by using conventional criteria (radiologists A and B: 46.7% and 74.2% and 91.3% and 84.8%, respectively).

CONCLUSION

When diagnosing T3 or T4 lung cancer based on arch distance-to-maximum tumor diameter ratios, a higher performance level was achieved than that with use of conventional criteria. Measurement of the ratios is a simple noninvasive technique for evaluating pleural invasion at CT.

摘要

目的

开发一种简单的无创技术,用于使用常规术前计算机断层扫描(CT)评估胸膜侵犯。

材料与方法

该机构审查委员会批准了这项回顾性研究,并获得了进行初始和随访 CT 研究的书面知情同意。评估了术前 CT 发现(169 例可能存在胸膜侵犯的患者)和手术后病理诊断。在 CT 图像上测量原发性肿瘤与邻近结构之间的界面长度(拱距)和最大肿瘤直径,然后计算拱距与最大肿瘤直径的比值。使用受试者工作特征(ROC)曲线分析这些比值。

结果

根据国际抗癌联盟 TNM 分期系统评估的胸膜侵犯类别(pl1、pl2、pl3)的中位拱距与最大肿瘤直径比值如下:pl1,0.206(25 百分位-75 百分位,0-0.486);pl2,0.638(25 百分位-75 百分位,0.385-0.830);pl3,1.092(25 百分位-75 百分位,1.045-1.214)(组间差异<.001)。基于 ROC 曲线,侵犯的临界值为拱距与最大肿瘤直径比值为 0.9。当比值大于 0.9 时,胸壁侵犯的敏感性、特异性和 ROC 曲线下面积分别为 89.7%、96.0%和 0.976,优于常规标准(放射科医师 A 和 B:分别为 46.7%和 74.2%,91.3%和 84.8%)。

结论

基于拱距与最大肿瘤直径比值诊断 T3 或 T4 肺癌时,比使用常规标准获得更高的性能水平。比值的测量是一种简单的无创技术,可用于 CT 评估胸膜侵犯。

文献检索

告别复杂PubMed语法,用中文像聊天一样搜索,搜遍4000万医学文献。AI智能推荐,让科研检索更轻松。

立即免费搜索

文件翻译

保留排版,准确专业,支持PDF/Word/PPT等文件格式,支持 12+语言互译。

免费翻译文档

深度研究

AI帮你快速写综述,25分钟生成高质量综述,智能提取关键信息,辅助科研写作。

立即免费体验