Frame James, Kamel Dia, Olivan Marcelo, Cintra Henrique
Postgraduate Medical Institute, Anglia Ruskin University, Bishop Hall Lane, Chelmsford, Essex, CM1 1SQ, UK,
Aesthetic Plast Surg. 2015 Oct;39(5):713-23. doi: 10.1007/s00266-015-0550-4. Epub 2015 Aug 25.
Polyurethane breast implants were first introduced by Ashley (Plast Reconstr Surg 45:421-424, 1970), with the intention of trying to reduce the high incidence of capsular contracture associated with smooth shelled, high gel bleed, silicone breast implants. The sterilization of the polyurethane foam in the early days was questionable. More recently, ethylene oxide (ETO)-sterilized polyurethane has been used in the manufacturing process and this has been shown to reduce the incidence of biofilm. The improved method of attachment of polyurethane onto the underlying high cohesive gel, barrier shell layered, silicone breast implants also encourages bio-integration. Polyurethane covered, cohesive gel, silicone implants have also been shown to reduce the incidence of other problems commonly associated with smooth or textured silicone implants, especially with reference to displacement, capsular contracture, seroma, reoperation, biofilm and implant rupture. Since the introduction of the conical polyurethane implant (Silimed, Brazil) into the United Kingdom in 2009 (Eurosurgical, UK), we have had the opportunity to review histology taken from the capsules of polyurethane implants in three women ranging from a few months to over 3 years after implantation. All implants had been inserted into virgin subfascial, extra-pectoral planes. The results add to the important previously described histological findings of Bassetto et al. (Aesthet Plast Surg 34:481-485, 2010). Five distinct layers are identified and reasons for the development of each layer are discussed. Breast capsule around polyurethane implants, in situ for fifteen and 20 years, has recently been obtained and analysed in Brazil, and the histology has been incorporated into this study. After 20 years, the polyurethane is almost undetectable and capsular contracture may appear. These findings contribute to our understanding of polyurethane implant safety, and give reasoning for a significant reduction in clinical capsular contracture rate, up to 10 years after implantation, compared to contemporary silicone implants. A more permanent matrix equivalent to polyurethane may be the solution for reducing long-term capsular contracture.
This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 .
聚氨酯乳房植入物最早由阿什利引入(《整形重建外科》45:421 - 424, 1970),目的是试图降低与光滑外壳、高凝胶渗漏的硅胶乳房植入物相关的包膜挛缩高发生率。早期聚氨酯泡沫的灭菌存在问题。最近,环氧乙烷(ETO)灭菌的聚氨酯已用于制造过程,且已证明这可降低生物膜的发生率。将聚氨酯附着于底层高粘性凝胶、屏障壳层的硅胶乳房植入物的改进方法也促进了生物整合。聚氨酯覆盖的粘性凝胶硅胶植入物也已证明可降低通常与光滑或有纹理的硅胶植入物相关的其他问题的发生率,特别是在移位、包膜挛缩、血清肿、再次手术、生物膜和植入物破裂方面。自2009年圆锥形聚氨酯植入物(巴西Silimed公司)引入英国(英国Eurosurgical公司)以来,我们有机会回顾了3名女性聚氨酯植入物包膜的组织学情况,这些女性植入时间从几个月到3年多不等。所有植入物均植入原始的筋膜下、胸外平面。这些结果补充了巴塞托等人之前描述的重要组织学发现(《美容整形外科》34:481 - 485, 2010)。识别出了五个不同的层,并讨论了每层形成的原因。最近在巴西获取并分析了在原位放置15年和20年的聚氨酯植入物周围的乳房包膜,其组织学已纳入本研究。20年后,聚氨酯几乎无法检测到,可能会出现包膜挛缩。这些发现有助于我们理解聚氨酯植入物的安全性,并为与当代硅胶植入物相比植入后长达10年临床包膜挛缩率显著降低提供了原因。一种更持久的等同于聚氨酯的基质可能是降低长期包膜挛缩的解决方案。
证据水平V:本刊要求作者为每篇文章指定证据水平。有关这些循证医学评级的完整描述,请参阅目录或作者在线指南www.springer.com/00266 。