Aboud Damon G K, Kietzig Anne-Marie
Department of Chemical Engineering, McGill University , Montreal QC H3A 0C5, Canada.
Langmuir. 2015 Sep 15;31(36):10100-11. doi: 10.1021/acs.langmuir.5b02447. Epub 2015 Sep 4.
Oblique drop impacts were performed at high speeds (up to 27 m/s, We > 9000) with millimetric water droplets, and a linear model was applied to define the oblique splashing threshold. Six different sample surfaces were tested: two substrate materials of different inherent surface wettability (PTFE and aluminum), each prepared with three different surface finishes (smooth, rough, and textured to support superhydrophobicity). Our choice of surfaces has allowed us to make several novel comparisons. Considering the inherent surface wettability, we discovered that PTFE, as the more hydrophobic surface, exhibits lower splashing thresholds than the hydrophilic surface of aluminum of comparable roughness. Furthermore, comparing oblique impacts on smooth and textured surfaces, we found that asymmetrical spreading and splashing behaviors occurred under a wide range of experimental conditions on our smooth surfaces; however, impacts occurring on textured surfaces were much more symmetrical, and one-sided splashing occurred only under very specific conditions. We attribute this difference to the air-trapping nature of textured superhydrophobic surfaces, which lowers the drag between the spreading lamella and the surface. The reduced drag affects oblique drop impacts by diminishing the effect of the tangential component of the impact velocity, causing the impact behavior to be governed almost exclusively by the normal velocity. Finally, by comparing oblique impacts on superhydrophobic surfaces at different impact angles, we discovered that although the pinning transition between rebounding and partial rebounding is governed primarily by the normal impact velocity, there is also a weak dependence on the tangential velocity. As a result, pinning is inhibited in oblique impacts. This led to the observation of a new behavior in highly oblique impacts on our superhydrophobic surfaces, which we named the stretched rebound, where the droplet is extended into an elongated pancake shape and rebounds while still outstretched, without exhibiting a recession phase.
采用毫米级水滴以高速(最高可达27米/秒,韦伯数>9000)进行斜向液滴撞击实验,并应用线性模型来定义斜向飞溅阈值。测试了六种不同的样品表面:两种具有不同固有表面润湿性的基底材料(聚四氟乙烯和铝),每种材料都制备了三种不同的表面光洁度(光滑、粗糙和具有超疏水性纹理)。我们对表面的选择使我们能够进行一些新颖的比较。考虑到固有表面润湿性,我们发现,作为疏水性更强的表面,聚四氟乙烯的飞溅阈值低于粗糙度相当的亲水性铝表面。此外,通过比较光滑表面和有纹理表面上的斜向撞击,我们发现在广泛的实验条件下,光滑表面上会出现不对称的铺展和飞溅行为;然而,有纹理表面上的撞击更加对称,只有在非常特殊的条件下才会出现单侧飞溅。我们将这种差异归因于有纹理的超疏水表面的空气捕获特性,这降低了铺展薄片与表面之间的阻力。阻力的降低通过减小撞击速度切向分量的影响来影响斜向液滴撞击,使得撞击行为几乎完全由法向速度控制。最后,通过比较不同撞击角度下超疏水表面上的斜向撞击,我们发现尽管反弹和部分反弹之间的钉扎转变主要由法向撞击速度控制,但也对切向速度有微弱的依赖性。因此,在斜向撞击中钉扎受到抑制。这导致在我们的超疏水表面上观察到一种在高度斜向撞击中的新行为,我们将其命名为拉伸反弹,即液滴伸展成细长的薄饼形状并在仍然伸展的状态下反弹,而不出现回缩阶段。