Ay Gurava Reddy, D Soundar Rajan, T Chiranjeevi, C Karthik, E Krishna Kiran
Department of Orthopaedics, Sunshine Hospitals, Secundrabad, India.
Department of Orthopaedics, Max cure Hospitals, Madhapur, India.
J Orthop Case Rep. 2016 Jul-Aug;6(3):35-37. doi: 10.13107/jocr.2250-0685.492.
Disengagement of polyethylene insert used in total knee arthroplasty is a rare but serious complication. Still rarer is disengagement because of failure of tibial insert locking mechanism. We report a previously unpublished complication of polyethylene insert locking mechanism failure in a 10-months-old posterior stabilized total knee arthroplasty in a 70-year-old woman with osteoarthritis for whom Attune (Depuy) knee implant was used.
A 70-year-old female underwent (Attune, Depuy) primary bilateral posterior stabilised total knee arthroplasty in a private hospital. The patient did not have any complaints and had had been functioning well post her arthroplasty. After five months of surgery she had a fall and sustained injury over right hip which was treated with Cemented Bipolar Hemiarthroplasty. Ten months after index surgery, she sustained trivial fall and presented to the same hospital with knee pain and swelling, where the right knee prosthesis was found to be dislocated. An attempted closed reduction under anaesthesia failed, after which she was referred to our centre with an unstable, painful, swollen right knee in a long knee brace. The physical examination at the time of admission showed posterior sag of the tibia, fullness in the postero-lateral corner, quadriceps muscle atrophy without any neurovascular deficit oflower leg. Postero-lateral dislocation was confirmed with radiographs. Surgical error as a possible causative factor was excluded because patient had been functioning well after surgery. Her comorbidities included hypertension and hyponatremia. ESR and CRP were within normal limits. An open reduction surgery was planned. On exposure, polyethylene was found in the postero-lateral corner of the knee. We were not sure that revising the polyethylene alone would suffice as the poly and locking mechanism was of a relatively new design and hence it was decided to proceed with revision of the components. Revision was done with stemmed components, distal femoral augments and a constrained prosthesis (Total Condylar 3, Depuy). Intraoperative cultures were negative. The patient had an uncomplicated post-operative course.
Disengagement of polyethylene should be considered as a differential diagnosis in patients who present with acute swelling and instability of the knee. Though it's a rare complication, there is a possibility that design of the implant or its locking mechanism could contribute to dislocations in future.
全膝关节置换术中使用的聚乙烯衬垫脱离是一种罕见但严重的并发症。因胫骨衬垫锁定机制故障导致的脱离则更为罕见。我们报告了一例此前未发表的聚乙烯衬垫锁定机制故障并发症,该病例发生在一名70岁患骨关节炎的女性患者身上,其接受了10个月前植入的Attune(Depuy)膝关节假体的后稳定型全膝关节置换术。
一名70岁女性在一家私立医院接受了(Attune,Depuy)初次双侧后稳定型全膝关节置换术。患者术后无任何不适,功能良好。术后五个月,她摔倒并导致右髋部受伤,接受了骨水泥型双极半髋关节置换术治疗。初次手术后十个月,她再次轻微摔倒,因膝关节疼痛和肿胀到同一家医院就诊,检查发现右膝假体脱位。在麻醉下尝试闭合复位失败,之后她被转诊至我们中心,右膝不稳定、疼痛且肿胀,戴着长腿膝关节支具。入院时体格检查显示胫骨后沉、后外侧角饱满、股四头肌萎缩,小腿无任何神经血管损伤。X线片证实为后外侧脱位。由于患者术后功能良好,排除了手术失误作为可能的致病因素。她的合并症包括高血压和低钠血症。血沉和C反应蛋白在正常范围内。计划进行切开复位手术。术中发现膝关节后外侧角有聚乙烯。由于聚乙烯和锁定机制设计相对较新,我们不确定仅更换聚乙烯是否足够,因此决定对组件进行翻修。使用带柄组件、股骨远端增强件和限制性假体(Total Condylar 3,Depuy)进行了翻修。术中培养结果为阴性。患者术后恢复顺利。
对于出现膝关节急性肿胀和不稳定的患者,应将聚乙烯衬垫脱离作为鉴别诊断之一。尽管这是一种罕见的并发症,但植入物的设计或其锁定机制有可能导致未来的脱位。