Pakeliani David, Lachat Mario, Blohmé Linus, Kobayashi Misato, Chaykovska Lyubov, Pfammatter Thomas, Puippe Gilbert, Veith Frank J, Pecoraro Felice
Clinic for Cardiovascular Surgery, University Hospital Zurich, Zurich, Switzerland.
Vascular Surgery Unit, Ospedali Riuniti Villa Sofia-Cervello, Palermo, Italy.
Vasa. 2020 Jan;49(1):39-42. doi: 10.1024/0301-1526/a000820. Epub 2019 Sep 24.
To present a technique of sheath supported contralateral limb gate (CLG) cannulation of modular bifurcated stent-graft in endovascular abdominal aortic repair. After totally percutaneous bilateral femoral access, the 9F introducer sheath is exchanged to a 30 cm 12 fr introducer sheath over a stiff wire contralateral to the intended main stent-graft insertion side and advanced into the aorta below the lowest renal artery. Parallel to the stiff wire within the sheath an additional standard J-tip guidewire with a 5 fr Pigtail angiographic catheter is advanced to the level of the renal arteries. After main body deployment, the 12 fr introducer sheath and J-tip wire with pigtail catheter are retracted until the CLG opening level, maintaining the stiff "buddy" wire in position to support the 12 fr sheath, maintaining its distal opening close to the contralateral gate opening to achieve easy cannulation. Retrospective analysis of video archive from July 2016 to February 2018 evidenced 55 recorded EVAR cases. All CLG cannulations were obtained with Standard J-tip or Terumo Glidewire wires and with Pig-Tail or Berenstein catheters. Technical success was 100 %. Mean fluoroscopy time to accomplish CLG cannulation was 37.6 33 (range 1-105) seconds. The aortic carrefour angulation on coronal axis strongly correlates with cannulation time p = <.001, with longer cannulation time for higher carrefour angulations on coronal axis (Pearson correlation coefficient 0.47). The use of 12 fr sheath with parallel wire introduction technique, appears to be a safe and reliable tool to facilitate CLG cannulation during EVAR procedures.
介绍一种在血管腔内腹主动脉修复术中,使用鞘管辅助对侧肢体门控(CLG)插管技术,将模块化分叉型覆膜支架置入的方法。在完全经皮双侧股动脉穿刺入路后,将9F导入鞘管通过一根硬导丝,更换为一根30cm长的12F导入鞘管,该硬导丝位于预期主覆膜支架置入侧的对侧,并推进至最低肾动脉下方的主动脉内。在鞘管内与硬导丝平行,将一根额外的标准J型头导丝和一根5F猪尾形血管造影导管推进至肾动脉水平。主体支架置入后,将12F导入鞘管以及带有猪尾导管的J型头导丝回撤至CLG开口水平,同时保持硬“伙伴”导丝在位,以支撑12F鞘管,使其远端开口靠近对侧门控开口,以实现轻松插管。对2016年7月至2018年2月的视频存档进行回顾性分析,证实有55例记录在案的血管腔内腹主动脉修复术(EVAR)病例。所有CLG插管均使用标准J型头或泰尔茂滑导丝以及猪尾或贝伦斯坦导管完成。技术成功率为100%。完成CLG插管的平均透视时间为37.6±33(范围1 - 105)秒。主动脉分叉在冠状轴上的角度与插管时间密切相关(p = <.001),冠状轴上主动脉分叉角度越大,插管时间越长(皮尔逊相关系数0.47)。在EVAR手术中,使用12F鞘管并行导丝引入技术似乎是一种安全可靠的工具,有助于CLG插管。