.
Acta Biomed. 2020 Sep 7;91(3):e2020057. doi: 10.23750/abm.v91i3.7769.
The modern approach to primary and secondary muscular skeletal tumors is multidisciplinary. The right combination of chemotherapy, surgery and radiotherapy (RT) makes obtaining local and distant disease control more likely. When surgery is indicated, radiotherapy often has a fundamental role as an adjuvant treatment; however, the titanium alloy instrumentations interfere with Radiotherapy setting, decreasing its effectiveness. It is common opinion that carbon fiber-reinforced devices are convenient in case of adjuvant RT in muscular skeletal oncology. The aim of the study is to support this intuition with experimental data, verifying the more accurate estimation of the delivered dose during RT, comparing Carbon Fiber-Reinforced PEEK (CFRP) plates with titanium-alloy orthopedic devices in order to evaluate their effects on target volume identification and dose distribution for radiation treatment.
Phantoms were then irradiated with a linear accelerator Varian 2100 C/D with photon beams of 6 and 15 MV energies. Absorbed dose in the point of interest was verified by EBT3 gafchromic films above and below the two materials. Images from CT simulations were also analyzed in terms of Hounsfield numbers in patients with titanium and carbon fiber orthopedic implants in the spine or in the femur.
For a 6 MV photon beam, the doses measured just under the titanium-alloy plate were less than approximately 20% of the value calculated by the TPS. For a 15 MV beam energy, these differences were slightly lower. Using CFRP plate, the difference between measured and calculated doses was within ±3% for both energies, which was comparable with the statistical uncertainties. In the cases of simulated treatment of humerus titanium implants, the difference varies in range ± 10% with hot spot of + 10% and cold spot of -15%.
The use of CFRP for orthopedic devices and implants provides a valuable advantage in identifying the target due to the reduction of artifacts. Clear imaging of the soft tissues surrounding the bone is useful and reduces the discrepancies between calculated/delivered and measured doses, generating a more homogeneous dose distribution. Furthermore, there is a significant benefit in detecting the state of disease in CT imaging during the follow-up of treated patients. In-vivo studies are encouraged to verify whether a more effective radiotherapy leads to a decrease in local recurrence and local progression.
原发性和继发性肌肉骨骼肿瘤的现代治疗方法是多学科的。化疗、手术和放疗(RT)的正确结合使获得局部和远处疾病控制的可能性更大。当需要手术时,放疗通常作为辅助治疗发挥着重要作用;然而,钛合金器械会干扰放疗设置,降低其效果。人们普遍认为,在肌肉骨骼肿瘤学中,碳纤维增强设备在辅助 RT 中非常方便。本研究的目的是用实验数据支持这种直觉,通过比较碳纤维增强聚醚醚酮(CFRP)板与钛合金骨科器械,验证在 RT 过程中更准确地估计递送剂量,以评估它们对靶区识别和剂量分布的影响。
然后使用瓦里安 2100 C/D 直线加速器用 6 和 15 MV 光子束对模型进行照射。在两种材料上方和下方用 EBT3 高氯酸盐胶片验证感兴趣点的吸收剂量。还根据脊柱或股骨中有钛和碳纤维骨科植入物的患者的 CT 模拟图像中的 Hounsfield 数进行分析。
对于 6 MV 光子束,在钛合金板下测量的剂量小于 TPS 计算值的约 20%。对于 15 MV 束能量,这些差异略低。对于 CFRP 板,两种能量下测量和计算剂量之间的差异在±3%以内,这与统计不确定性相当。在模拟肱骨钛植入物治疗的情况下,差异在±10%范围内变化,热点为+10%,冷点为-15%。
由于减少了伪影,因此在识别目标方面,碳纤维增强用于骨科器械和植入物具有重要优势。骨骼周围软组织的清晰成像很有用,并减少了计算/递送剂量和测量剂量之间的差异,从而产生更均匀的剂量分布。此外,在治疗患者的随访中,在 CT 成像中检测疾病状态具有重要意义。鼓励进行体内研究,以验证更有效的放疗是否会降低局部复发和局部进展的风险。