Almashraqi Abeer A
Department of Maxillofacial Surgery and Diagnostic Sciences, College of Dentistry, Jazan University, Jazan, Kingdom of Saudi Arabia, Phone: +966502210865, e-mail:
J Contemp Dent Pract. 2020 Oct 1;21(10):1075-1083.
This retrospective cross-sectional study investigated the dimensional and positional associations between the mandibular condyle and glenoid fossa (GF) using cone-beam computed tomography (CBCT).
Seventy female subjects [140 temporomandibular joints (TMJs)] were divided into two groups. Group I included 35 subjects with normal facial profiles (NFPs) in which the soft tissue glabella, subnasal point, and the soft tissue chin are almost in the same straight line, while the 35 subjects in group II had abnormal facial profiles (AFPs) in which the same imaginary line is either convex or concave indicating variation from standard norms. Three-dimensional volume analyses were performed on CBCT images by digitizing all landmarks in three orthogonal planes to measure the dimensional and positional parameters of the condyle and GF. Then the Pearson's correlation coefficient was used to identify associations between different condyle and GF parameters.
Sagittal condylar surface area was significantly associated with all dimensional parameters of the GF (GF height, width, and surface area, condylar width, and the GF width and between the axial and coronal condylar surface area with GF height and GF width) on the right and left sides of both groups ( values ranging from 0.000 to 0.028). Positional associations were detected between the anteroposterior and mediolateral GF positions and the corresponding position of the mandibular condyles and between the anteroposterior condylar position and the vertical GF position on both sides of both groups ( values ranged from 0.000 to 0.015).
There is a strong association between the mandibular condyle and GF in both positional and dimensional measurements in patients with normal and abnormal facial profiles.
Understanding the associations between the mandibular condyle and GF facilitates optimization of the treatment outcomes by increasing occlusal harmony and stability after orthodontic treatment, orthognathic surgery, or any prosthetic replacement.
本回顾性横断面研究使用锥形束计算机断层扫描(CBCT)调查下颌髁突与关节窝(GF)之间的尺寸和位置关联。
70名女性受试者[140个颞下颌关节(TMJ)]被分为两组。第一组包括35名面部轮廓正常(NFP)的受试者,其软组织眉间点、鼻下点和软组织颏部几乎在同一直线上,而第二组的35名受试者面部轮廓异常(AFP),同一条假想线呈凸形或凹形,表明与标准规范存在差异。通过在三个正交平面上数字化所有标志点,对CBCT图像进行三维体积分析,以测量髁突和关节窝的尺寸和位置参数。然后使用Pearson相关系数来确定不同髁突和关节窝参数之间的关联。
两组左右两侧的矢状髁突表面积与关节窝的所有尺寸参数(关节窝高度、宽度和表面积、髁突宽度,以及关节窝宽度和轴向与冠状髁突表面积之间与关节窝高度和关节窝宽度)均显著相关(值范围为0.000至0.028)。在两组两侧的关节窝前后和内外侧位置与下颌髁突的相应位置之间,以及髁突前后位置与关节窝垂直位置之间检测到位置关联(值范围为0.000至0.015)。
在面部轮廓正常和异常的患者中,下颌髁突与关节窝在位置和尺寸测量方面均存在密切关联。
了解下颌髁突与关节窝之间的关联有助于通过在正畸治疗、正颌手术或任何假体置换后提高咬合协调性和稳定性来优化治疗效果。