Suppr超能文献

碱激发材料单组分混合方法的思考:硅酸钠溶解性和速凝问题

A consideration on the one-part mixing method of alkali-activated material: problems of sodium silicate solubility and quick setting.

作者信息

Rasuli Mohammad Idris, Tajunnisa Yuyun, Yamamura Akifumi, Shigeishi Mitsuhiro

机构信息

Graduate School of Science and Technology, Kumamoto University, 2-39-1 Kurokami, Chuo-ku, Kumamoto, 860-8555, Japan.

Institut Teknologi Sepuluh Nopember (ITS), Kampus ITS Manyar, Jl. Menur 127, Surabaya, 60116, Indonesia.

出版信息

Heliyon. 2022 Jan 17;8(1):e08783. doi: 10.1016/j.heliyon.2022.e08783. eCollection 2022 Jan.

Abstract

This research investigates the properties of alkali-activated materials (AAMs) using sodium metasilicate, with the ratio of SiO:NaO equals 1. This study was conducted to achieve the following three aims. Firstly, to understand the solubility mechanism of granular sodium metasilicate pentahydrate (NaSiO.5HO) when used in a one-part mixing method. Secondly, to investigate the properties of AAMs when a sodium metasilicate aqueous solution is used as an alkaline material and as a source of silica. Lastly, to study the retardation effect of sucrose on AAMs. This research used aluminum silicate precursors, such as low-calcium fly ash, slag, and micros silica, alkali activators, such as NaOH pellets and NaSiO.5HO, and standardized sand. The alkaline activators were first dissolved in water using a water bath shaker to achieve the alkaline solution. Sucrose, which is about 2% of the weight of the solid precursors, was added to modify the reaction process between the precursors and the alkaline materials. Four types of samples were prepared: M1, M2, M3, and M4, with the fly ash, slag, and silica fume ratios of 80:20:0, 70:30:0, 75:20:5, and 100:0:0, respectively. The research conducted solubility test of the alkaline materials, flowability, 7-, 28-, 56-day compressive and flexural tests, drying shrinkage test of mortar samples, and the setting tests of pastes with and without sucrose. The results show that the dissolution time of the NaOH was much shorter, whereas NaSiO.5HO needed a solvent with a temperature of around 40 °C to be fully dissolved. This problem of solubility decreases the quality of AAMs formed using the one-part mixing method. Among the mortar samples, the M4 had the highest flow rate, while M3 had the lowest flow rate. M2 had the highest compressive and flexural strength of 43.4 MPa and 6.1 MPa, respectively. The setting time test shows that sucrose retards the reaction process in AAM.

摘要

本研究使用硅酸钠研究碱激活材料(AAMs)的性能,SiO与NaO的比例为1。进行本研究以实现以下三个目标。首先,了解五水偏硅酸钠颗粒(NaSiO·5HO)在单组分混合方法中使用时的溶解机理。其次,研究以硅酸钠水溶液作为碱性材料和硅源时AAMs的性能。最后,研究蔗糖对AAMs的缓凝作用。本研究使用硅酸铝前驱体,如低钙粉煤灰、矿渣和微硅粉,碱激活剂,如氢氧化钠颗粒和NaSiO·5HO,以及标准砂。首先使用水浴振荡器将碱性激活剂溶解在水中以获得碱性溶液。添加约为固体前驱体重量2%的蔗糖以改变前驱体与碱性材料之间的反应过程。制备了四种类型的样品:M1、M2、M3和M4,粉煤灰、矿渣和硅灰的比例分别为80:20:0、70:30:0、75:20:5和100:0:0。该研究对碱性材料进行了溶解度测试、流动性测试、7天、28天、56天的抗压和抗折测试、砂浆样品的干燥收缩测试以及有无蔗糖的浆料的凝结测试。结果表明,NaOH的溶解时间短得多,而NaSiO·5HO需要温度约为40°C的溶剂才能完全溶解。这种溶解度问题降低了使用单组分混合方法形成的AAMs的质量。在砂浆样品中,M4的流速最高,而M3的流速最低。M2的抗压强度和抗折强度最高,分别为43.4MPa和6.1MPa。凝结时间测试表明,蔗糖会延缓AAM中的反应过程。

https://cdn.ncbi.nlm.nih.gov/pmc/blobs/cb78/8790622/bd43b8b30e07/gr1.jpg

文献AI研究员

20分钟写一篇综述,助力文献阅读效率提升50倍。

立即体验

用中文搜PubMed

大模型驱动的PubMed中文搜索引擎

马上搜索

文档翻译

学术文献翻译模型,支持多种主流文档格式。

立即体验