Baleani Massimiliano, Erani Paolo, Blaise Manon, Fognani Roberta, Palmas Marco, Manfrini Marco
Laboratorio di Tecnologia Medica, IRCCS Istituto Ortopedico Rizzoli, Bologna, Italy.
Clinica Ortopedica e Traumatologica III a Prevalente Indirizzo Oncologico, IRCCS Istituto Ortopedico Rizzoli, Bologna, Italy.
Front Pediatr. 2022 Aug 3;10:868299. doi: 10.3389/fped.2022.868299. eCollection 2022.
An intercalary segmental allograft is an option for limb salvage in bone tumours. Stable and congruent intercalary reconstructions are a prerequisite for achieving host-graft union. However, a too rigid fixation could increase the risk of late complications correlated with negative bone remodelling. This study compared the reconstruction stiffness achieved by three different host-graft junctions, namely, end-to-end, modified step-cut, and taper. A low-stiffness bone plate was used as the fixation method, except for the taper junction where a low-stiffness intramedullary nail was also used to investigate the effects of different types of fixation on construct stiffness. Composite femora were tested under four loading conditions to determine coronal and sagittal bending stiffness, as well as torsional stiffness in opposite directions. Stiffness values were expressed as a percentage of intact host bone stiffness (%IBS). While a reduction of coronal bending stiffness was found with taper junctions (76%IBS) compared with the high values ensured by end-to-end (96%IBS) and modified step-cut junctions (92%IBS), taper junctions significantly increased stiffness under sagittal bending and torsion in intra- and extra-direction: end-to-end 29%IBS, 7%IBS, 7%IBS, modified step-cut 38%IBS, 20%IBS, 21%IBS, and taper junction 52%IBS, 55%IBS, 56%IBS, respectively. Construct stiffness with taper junctions was decreased by 11-41%IBS by replacing the bone plate with an intramedullary nail. Taper junctions can be an alternative to achieve intercalary reconstructions with more homogeneous and, in three out of four loading conditions, significantly higher construct stability without increasing bone plate stiffness. The risk of instability under high torsional loads increases when taper junctions are associated with a low-stiffness intramedullary nail.
节段间同种异体移植是骨肿瘤保肢的一种选择。稳定且匹配的节段间重建是实现宿主与移植物融合的前提条件。然而,过于刚性的固定可能会增加与负性骨重塑相关的晚期并发症风险。本研究比较了三种不同宿主 - 移植物连接方式(即端端连接、改良阶梯状连接和锥形连接)所实现的重建刚度。除了锥形连接使用低刚度髓内钉外,其他连接方式均采用低刚度接骨板作为固定方法,以研究不同类型固定对结构刚度的影响。对复合股骨在四种加载条件下进行测试,以确定冠状面和矢状面弯曲刚度以及相反方向的扭转刚度。刚度值以完整宿主骨刚度的百分比(%IBS)表示。与端端连接(96%IBS)和改良阶梯状连接(92%IBS)所确保的高值相比,锥形连接的冠状面弯曲刚度有所降低(76%IBS),但在矢状面弯曲和内外方向扭转时,锥形连接显著增加了刚度:端端连接分别为29%IBS、7%IBS、7%IBS,改良阶梯状连接分别为38%IBS、20%IBS、21%IBS,锥形连接分别为52%IBS、55%IBS、56%IBS。用髓内钉替代接骨板后,锥形连接结构的刚度降低了11 - 41%IBS。锥形连接可作为一种替代方法来实现节段间重建,在四种加载条件中的三种情况下,其结构稳定性更均匀且显著更高,同时不增加接骨板刚度。当锥形连接与低刚度髓内钉联合使用时,在高扭转载荷下不稳定的风险会增加。