Schwartz Z, Martin J Y, Dean D D, Simpson J, Cochran D L, Boyan B D
Department of Periodontics, Hebrew University Hadassah Faculty of Dental Medicine, Jerusalem, Israel.
J Biomed Mater Res. 1996 Feb;30(2):145-55. doi: 10.1002/(SICI)1097-4636(199602)30:2<145::AID-JBM3>3.0.CO;2-R.
Although it is well accepted that implant success is dependent on various surface properties, little is known about the effect of surface roughness on cell metabolism or differentiation, or whether the effects vary with the maturational state of the cells interacting with the implant. In the current study, we examined the effect of titanium (Ti) surface roughness on chondrocyte proliferation, differentiation, and matrix synthesis using cells derived from known stages of endochondral development. Chondrocytes derived from the resting zone (RCs) and growth zone (GCs) of rat costochondral cartilage were cultured on Ti disks that were prepared as follows: HF-HNO3-treated and washed (PT); PT-treated and electropolished (EP); fine sand-blasted, HCl-H2SO4-etched, and washed (FA); coarse sand-blasted, HCl-H2SO4-etched, and washed (CA); or Ti plasma-sprayed (TPS). Based on surface analysis, the Ti surfaces were ranked from smoothest to roughest: EP, PT, FA, CA, and TPS. Cell proliferation was assessed by cell number and [3H]-thymidine incorporation, and RNA synthesis was assessed by [3H]-uridine incorporation. Differentiation was determined by alkaline phosphatase specific activity (AL-Pase). Matrix production was measured by [3H]-proline incorporation into collagenase-digestible (CDP) and noncollagenase-digestible (NCP) protein and by [35S]-sulfate incorporation into proteoglycan. GCs required two trypsinizations for complete removal from the culture disks; the number of cells released by the first trypsinization was generally decreased with increasing surface roughness while that released by the second trypsinization was increased. In RC cultures, cell number was similarly decreased on the rougher surfaces; only minimal numbers of RCs were released by a second trypsinization. [3H]-thymidine incorporation by RCs decreased with increasing surface roughness while that by GCs was increased. [3H]-Uridine incorporation by both GCs and RCs was greater on rough surfaces. Conversely, ALPase in the cell layer and isolated cells of both cell types was significantly decreased. GC CDP and NCP production was significantly decreased on rough surfaces while CDP production by RC cells was significantly decreased on smooth surfaces. [35S]-sulfate incorporation by RCs and GCs was decreased on all surfaces compared to tissue culture plastic. The results of this study indicate that surface roughness affects chondrocyte proliferation, differentiation, and matrix synthesis, and that this regulation is cell maturation dependent.
尽管人们普遍认为种植体的成功取决于各种表面特性,但对于表面粗糙度对细胞代谢或分化的影响,或者这种影响是否会因与种植体相互作用的细胞的成熟状态而有所不同,却知之甚少。在本研究中,我们使用源自软骨内发育已知阶段的细胞,研究了钛(Ti)表面粗糙度对软骨细胞增殖、分化和基质合成的影响。将大鼠肋软骨静止区(RCs)和生长区(GCs)的软骨细胞培养在按以下方式制备的Ti盘上:氢氟酸 - 硝酸处理并洗涤(PT);PT处理后进行电解抛光(EP);细喷砂、盐酸 - 硫酸蚀刻并洗涤(FA);粗喷砂、盐酸 - 硫酸蚀刻并洗涤(CA);或Ti等离子喷涂(TPS)。基于表面分析,Ti表面按从最光滑到最粗糙的顺序排列为:EP、PT、FA、CA和TPS。通过细胞数量和[3H] - 胸腺嘧啶核苷掺入评估细胞增殖,通过[3H] - 尿苷掺入评估RNA合成。通过碱性磷酸酶比活性(AL - Pase)确定分化。通过[3H] - 脯氨酸掺入胶原酶可消化(CDP)和非胶原酶可消化(NCP)蛋白以及通过[35S] - 硫酸盐掺入蛋白聚糖来测量基质产生。GCs需要两次胰蛋白酶消化才能从培养盘上完全去除;第一次胰蛋白酶消化释放的细胞数量通常随着表面粗糙度的增加而减少,而第二次胰蛋白酶消化释放的细胞数量增加。在RC培养物中,较粗糙表面上的细胞数量同样减少;第二次胰蛋白酶消化仅释放极少量的RCs。RCs的[3H] - 胸腺嘧啶核苷掺入随着表面粗糙度的增加而减少,而GCs的则增加。粗糙表面上GCs和RCs的[3H] - 尿苷掺入都更多。相反,两种细胞类型的细胞层和分离细胞中的ALPase均显著降低。粗糙表面上GCs的CDP和NCP产生显著降低,而光滑表面上RC细胞的CDP产生显著降低。与组织培养塑料相比,所有表面上RCs和GCs的[35S] - 硫酸盐掺入均减少。本研究结果表明,表面粗糙度会影响软骨细胞的增殖、分化和基质合成,并且这种调节依赖于细胞成熟度。