Ishaug-Riley S L, Crane-Kruger G M, Yaszemski M J, Mikos A G
Institute of Biosciences and Bioengineering and Department of Chemical Engineering, Rice University, Houston, TX 77005-1892, USA.
Biomaterials. 1998 Aug;19(15):1405-12. doi: 10.1016/s0142-9612(98)00021-0.
Neonatal rat calvarial osteoblasts were cultured in 90% porous, 75:25 poly(DL-lactic-co-glycolic acid) (PLGA) foam scaffolds for up to 56 days to examine the effects of the cell seeding density, scaffold pore size, and foam thickness on the proliferation and function of the cells in this three-dimensional environment. Osteoblasts were seeded at either 11.1 x 10(5) or 22.1 x 10(5) cells per cm2 onto PLGA scaffolds having pore sizes in the range of 150-300 or 500-710 microm with a thickness of either 1.9 or 3.2 mm. After 1 day in culture, 75.6 and 68.6% of the seeded cells attached and proliferated on the 1.9 mm thick scaffolds of 150-300 microm pore size for the low and high seeding densities, respectively. The number of osteoblasts continued to increase throughout the study and eventually leveled off near 56 days, as indicated by a quantitative DNA assay. Osteoblast/foam constructs with a low cell seeding density achieved comparable DNA content and alkaline phosphatase (ALPase) activity after 14 days, and mineralization results after 56 days to those with a high cell seeding density. A maximum penetration depth of osseous tissue of 220+/-40 microm was reached after 56 days in the osteoblast/foam constructs of 150-300 microm pore size initially seeded with a high cell density. For constructs of 500-710 microm pore size, the penetration depth was 190+/-40 microm under the same conditions. Scaffold pore size and thickness did not significantly affect the proliferation or function of osteoblasts as demonstrated by DNA content, ALPase activity, and mineralized tissue formation. These data show that comparable bone-like tissues can be engineered in vitro over a 56 day period using different rat calvarial osteoblast seeding densities onto biodegradable polymer scaffolds with pore sizes in the range of 150-710 microm. When compared with the results of a previous study where similar polymer scaffolds were seeded and cultured with marrow stromal cells, this study demonstrates that PLGA foams are suitable substrates for osteoblast growth and differentiated function independent of cell source.
将新生大鼠颅骨成骨细胞培养在90%孔隙率、75:25聚(DL-乳酸-乙醇酸)(PLGA)泡沫支架中长达56天,以研究细胞接种密度、支架孔径和泡沫厚度对这种三维环境中细胞增殖和功能的影响。将成骨细胞以每平方厘米11.1×10⁵或22.1×10⁵个细胞的密度接种到孔径在150 - 300或500 - 710微米范围内、厚度为1.9或3.2毫米的PLGA支架上。培养1天后,对于低接种密度和高接种密度,分别有75.6%和68.6%的接种细胞附着并在孔径为150 - 300微米、厚度为1.9毫米的支架上增殖。定量DNA分析表明,在整个研究过程中,成骨细胞数量持续增加,最终在56天左右趋于平稳。低细胞接种密度的成骨细胞/泡沫构建体在14天后达到了与高细胞接种密度构建体相当的DNA含量和碱性磷酸酶(ALPase)活性,以及56天后的矿化结果。最初以高细胞密度接种的孔径为150 - 300微米的成骨细胞/泡沫构建体在56天后骨组织的最大穿透深度达到220±40微米。对于孔径为500 - 710微米的构建体,在相同条件下穿透深度为190±40微米。如DNA含量、ALPase活性和矿化组织形成所示,支架孔径和厚度对成骨细胞的增殖或功能没有显著影响。这些数据表明,使用不同的大鼠颅骨成骨细胞接种密度,在56天内可以在体外构建出类似骨组织的组织,接种到孔径在150 - 710微米范围内的可生物降解聚合物支架上。与之前一项将类似聚合物支架接种并培养骨髓基质细胞的研究结果相比,本研究表明PLGA泡沫是成骨细胞生长和分化功能的合适基质,与细胞来源无关。