Skrumeda L L, Mehra R
Medtronic, Inc., Minneapolis, Minnesota, USA.
J Cardiovasc Electrophysiol. 1998 Nov;9(11):1196-205. doi: 10.1111/j.1540-8167.1998.tb00092.x.
Radiofrequency ablation is successful for treating some arrhythmias but not for CAD-VT, possibly due to insufficient lesion size. Irrigated electrodes were developed to apply higher power for longer duration to create larger lesions. Our objective was to characterize and compare irrigated and standard ablation in terms of lesion size, crater, and coagulum formation. Additionally, a method is proposed for creating large irrigated lesions without craters.
Three ablation protocols were conducted in canine ventricles. Protocol I: standard ablation was performed in power mode at 10, 20, 30, and 50 W, and electrode-temperature mode at 70 degrees and 90 degrees C (120 sec). Protocol II: irrigated ablation was conducted with 30 and 50 W (30 and 120 sec). Protocol III: to create large lesions without craters, irrigated ablation was performed at 20 W (5 and 10 min). With a standard electrode, the largest lesions were created using 20 W (358+/-194 mm3) and using 90 degrees C (301+/-130 mm3). Ablation duration decreased with power for the power mode standard ablations. The largest irrigated lesions were formed using 50 W (986+/-357 mm3). Large lesions without craters were created with irrigation using 20 W for 10 minutes (602+/-175 mm3). Coagulum was seen for most standard ablations but infrequently for irrigated ablations. Craters were observed with 30 and 50 W irrigated ablation but were not observed with 20 W irrigated ablation.
Irrigated ablation created larger lesions than standard; large lesions may be created without craters using moderate power and long duration.
射频消融术在治疗某些心律失常方面取得了成功,但对冠心病室性心动过速(CAD-VT)却无效,这可能是由于消融损伤范围不足所致。为了能够更长时间地施加更高功率以形成更大的损伤范围,人们开发了灌注电极。我们的目的是从损伤范围、弹坑和凝块形成方面对灌注消融和标准消融进行特征描述和比较。此外,还提出了一种创建无弹坑的大灌注损伤范围的方法。
在犬类心室中进行了三种消融方案。方案I:在功率模式下分别以10、20、30和50瓦以及电极温度模式下70摄氏度和90摄氏度(持续120秒)进行标准消融。方案II:以30和50瓦(分别持续30和120秒)进行灌注消融。方案III:为了创建无弹坑的大损伤范围,以20瓦(分别持续5和10分钟)进行灌注消融。使用标准电极时,在20瓦(358±194立方毫米)以及90摄氏度(301±130立方毫米)条件下形成的损伤范围最大。对于功率模式的标准消融,消融持续时间随功率增加而减少。使用50瓦(986±357立方毫米)形成的灌注损伤范围最大。通过以20瓦持续灌注10分钟(602±175立方毫米)创建了无弹坑的大损伤范围。大多数标准消融可见凝块,但灌注消融中很少见。在30和50瓦的灌注消融中观察到了弹坑,但在20瓦的灌注消融中未观察到。
灌注消融产生的损伤范围比标准消融更大;使用中等功率和较长时间可以创建无弹坑的大损伤范围。