Schäfer E, Lohmann D
Department of Operative Dentistry, University of Münster, Münster, Germany.
Int Endod J. 2002 Jun;35(6):514-21. doi: 10.1046/j.1365-2591.2002.00515.x.
To determine the cleaning effectiveness and the shaping ability of FlexMaster nickel-titanium rotary instruments and stainless steel hand K-Flexofiles during the preparation of curved root canals in extracted human teeth.
A total of 48 root canals with curvatures ranging between 25 degrees and 35 degrees were divided into two groups of 24 canals. Based on radiographs taken prior to the instrumentation with the initial instrument inserted into the canal, the groups were balanced with respect to the angle and the radius of canal curvature. Canals were prepared by FlexMaster instruments using a crown-down preparation technique or by K-Flexofiles using a reaming working motion up to size 35. After each instrument, the root canals were flushed with 5 mL of a 2.5% NaOCl solution and at the end of instrumentation with 5 mL of NaCl. Using the pre- and post-instrumentation radiographs, straightening of the canal curvatures was determined with a computer image analysis program. After splitting the roots longitudinally, the amount of debris and smear layer were quantified on the basis of a numerical evaluation scale, using a scanning electron microscope.
Completely cleaned root canals were not found with any of the two instruments. In general, K-Flexofiles resulted in significantly less debris(P < 0.001) and less smear layer (P < 0.05) than Flex-Master instruments, but these differences were not significant in the apical third of the canals (P > 0.05). FlexMaster instruments maintained the original canal curvature significantly better (P < 0.0001) than K-Flexofiles. No significant differences were detected between the instruments (P > 0.05) for the time taken to prepare the canals.
Under the conditions of this study, K-Flexofiles allowed significantly better canal cleaning than FlexMaster instruments. FlexMaster instruments maintained the original curvature significantly better.
确定FlexMaster镍钛旋转器械和不锈钢手动K-Flex锉在预备拔除的人牙弯曲根管时的清洁效果和根管塑形能力。
选取48个弯曲度在25度至35度之间的根管,分为两组,每组24个根管。根据在器械预备前将初始器械插入根管时拍摄的X线片,两组在根管弯曲角度和半径方面保持平衡。使用FlexMaster器械采用冠向深入法预备根管,或使用K-Flex锉采用扩锉操作至35号。每个器械使用后,用5 mL 2.5%的次氯酸钠溶液冲洗根管,器械预备结束后用5 mL氯化钠溶液冲洗。利用器械预备前后的X线片,通过计算机图像分析程序确定根管弯曲度的变直情况。将牙根纵向劈开后,使用扫描电子显微镜,根据数字评估量表对碎屑和玷污层的量进行量化。
两种器械均未发现能将根管完全清洁的情况。总体而言,K-Flex锉产生的碎屑明显少于FlexMaster器械(P < 0.001),玷污层也少于FlexMaster器械(P < 0.05),但在根管根尖三分之一处这些差异不显著(P > 0.05)。FlexMaster器械保持原始根管弯曲度的效果明显优于K-Flex锉(P < 0.0001)。两种器械在预备根管所需时间上未检测到显著差异(P > 0.05)。
在本研究条件下,K-Flex锉在根管清洁方面明显优于FlexMaster器械。FlexMaster器械在保持原始弯曲度方面明显更好。