Palin W M, Fleming G J P, Burke F J T, Marquis P M, Randall R C
Biomaterials Unit, School of Dentistry, University of Birmingham, St Chad's Queensway, Birmingham B4 6NN, UK.
Dent Mater. 2005 Sep;21(9):852-63. doi: 10.1016/j.dental.2005.01.004.
Differences in mechanical and physical properties exhibited by novel low-shrink resin-based composite (RBC) formulations compared with conventional methacrylate RBCs may contribute to the clinical success of the candidate material. The aim of the current study was to investigate the effect of water uptake characteristics and water solubility on the mechanical properties of two methacrylate (Z100 and Filtek Z250), an experimental oxirane (OXI) and silorane (SIL) RBC following short- and medium-term immersion.
The water sorption/solubility and associated diffusion coefficients of each material (n=5) were measured using gravimetric analysis following short- (0.1, 0.5, 1, 4, 24 and 48 h) and medium-term (1, 4, 12 and 26w) immersion. The bi-axial flexure strength, associated Weibull moduli (n=20) and fracture analysis using scanning electron microscopy (SEM) of each material for similar immersion periods was also investigated.
Following 0.5h and each subsequent short- and medium-term immersion period the water sorption of Z100 and Filtek Z250 was decreased compared with OXI. A significant decrease in bi-axial flexure strength and associated increase in filler particle exfoliation identified through SEM was identified for OXI compared with Z100, Filtek Z250 and SIL following 26w immersion. SIL exhibited the significantly lowest water sorption, solubility and associated diffusion coefficient following each immersion period.
The increase in water sorption, solubility and the associated diffusion coefficient of the experimental oxirane RBC, OXI was manifested as a significant decrease in bi-axial flexure strength and attributed to the decrease in synergy between the filler particles and resin matrix. The decreased water sorption, solubility and associated diffusion coefficient of the experimental silorane RBC, SIL may potentially improve hydrolytic stability of RBC restorations demonstrated by the non-significant decrease in bi-axial flexure strength following medium-term immersion.
与传统甲基丙烯酸酯类树脂基复合材料(RBC)相比,新型低收缩RBC配方所表现出的机械和物理性能差异可能有助于候选材料在临床上取得成功。本研究的目的是调查两种甲基丙烯酸酯类材料(Z100和Filtek Z250)、一种实验性环氧乙烷(OXI)和硅氧烷(SIL)RBC在短期和中期浸泡后,吸水率特性和水溶性对其机械性能的影响。
在短期(0.1、0.5、1、4、24和48小时)和中期(1、4、12和26周)浸泡后,采用重量分析法测量每种材料(n=5)的吸水率/溶解度及相关扩散系数。还研究了每种材料在相似浸泡时间后的双轴弯曲强度、相关韦布尔模量(n=20)以及使用扫描电子显微镜(SEM)进行的断裂分析。
在0.5小时以及随后的每个短期和中期浸泡期后,Z100和Filtek Z250的吸水率均低于OXI。与Z100、Filtek Z250和SIL相比,OXI在浸泡26周后,双轴弯曲强度显著降低,且通过SEM发现填料颗粒剥落增加。在每个浸泡期后,SIL的吸水率、溶解度及相关扩散系数均显著最低。
实验性环氧乙烷RBC(OXI)的吸水率、溶解度及相关扩散系数增加,表现为双轴弯曲强度显著降低,这归因于填料颗粒与树脂基体之间协同作用的降低。实验性硅氧烷RBC(SIL)的吸水率、溶解度及相关扩散系数降低,可能会提高RBC修复体的水解稳定性,中期浸泡后双轴弯曲强度无显著降低即证明了这一点。